Labels Milestones
BackRel="nofollow">f51b7b97734e404127fa5d5d263acbfd66f116e4 Add schematic, start on PCB with exploratory 8hp layout 2x Sockets, all three pins need wires: - glide in (sleeve and normal both GND - Gate Out - 1K to U3-7 Glide section not working right, just pegging the output to +10V? Clock POT is too small for film; is film needed? More notes main synth_tools/3D Printing/Pot_Knobs/Potentiometer Cap.STL From c5e8dbdd1f5bb4b2a027556e63f3cebc1db3a56a Mon Sep 17 00:00:00 2001 Subject: [PATCH] SVG decontamination Hardware/Panel/precadsr_panel.svg | 4 .../PCB/precadsr_Gerbers/precadsr-F_Paste.gbr | 15 .../PCB/precadsr_Gerbers/precadsr-F_SilkS.gbr | 1166 .../PCB/precadsr_Gerbers/precadsr-NPTH.drl | 4 | 47k | Resistor | | | | | D6, D7 | 2 pin Molex header 2.54 mm spacing D 3 pin Molex header 2.54 mm spacing 2 pin Molex header 2.54 mm spacing | | | Tayda | A-1847 | | | J1 | 1 | B10k | **Potentiometer, 16 mm vertical board mount. Main MK_VCO/Panels/title_test.scad 40 lines default_label_font = "Futura XBlk BT:style=Extra Black"; // waves out // cv range (switch between 2.5v and 5v max // gate out (j4/j10 // clock out (j5/j12) // glide atten (rv15 // glide in (sleeve and normal both GND 6x Sockets, 2pin: - reset in - glide in (sleeve and normal both GND 6x Sockets, 2pin: Gate out (could normal to TP10, optional 2x Toggle Switches, 2pin: - all step switches (all go to same bus 2x Pushbutton switches, all 2pin: - Glide attenuator (B10k) (join two left pins from below - Clock rate goes down when resistance goes up, opposite to expectation. Schematic fixes: - C1 is too small; need more than 100k to get 1:1 between schematic and PCB, .../Unseen Servant/Unseen Servant.kicad_pcb create mode 100644 Hardware/PCB/precadsr_aux_Gerbers/precadsr-F_Mask.gbr create mode 100644 Hardware/PCB/precadsr/ao_tht.pretty/Potentiometer_Alpha_RA6020F_Single_Slide.kicad_mod create mode 100644 3D Printing/AD&D 1e spell names in Filmoscope Quentin/PRISMATIC SPHERE.png differ Binary files /dev/null and b/Panels/Font files/futura medium bt.ttf Latest commits for file Schematics/SynthMages.pretty/IDC-Header_2x05_P2.54mm_Vertical_Fixed_Ground_Fill.kicad_mod Fix annoyance of 2x05 IDC header triangle being so far out Add polygon calculation for wing plates bab77fac9d Add befaco image for inspo Add befaco image for inspo Compare 15 commits » 14162964f9 Add circuit blocks to kick drum schematic main arrasta/samba_reggae.txt 82 lines REP: repique CAX: caixa MSD: mid surdo (sometimes MS1, MS2, etc, if pattern spans measures or has planned variations) BSD: back surdo (L for low, H for high)
- System, 55935-1410, with PCB cutout.
- ============================================================= Total unplated holes.