Labels Milestones
BackOn with CA or hot glue, if the PCB is used. C1 is too small for a little wiggle room on the ~Env output. You can use it instead of latch, https://www.neutrik.com/en/product/nc3fahr1-0 A Series, 3 pole XLR female receptacle with 6.35mm (1/4in) stereo jack, switched, with chrome ferrule and offset PCB pins, https://www.neutrik.com/en/product/nmj6hfd4 M Series, 6.35mm (1/4in) stereo jack (T/R/S), https://www.neutrik.com/en/product/nj3fd-v 6.35mm (1/4 in) Vertical Jack, Non-switching mono jack without switching contact, vertical PCB mount, retention spring, https://www.neutrik.com/en/product/ncj10fi-v AA Series, 3 pole male XLR receptacle, grounding: separate ground contact to mating connector shell and front panel, vertical PCB mount, black chrome shell, https://www.neutrik.com/en/product/nc5mbh-b B Series, 3 pole female XLR receptacle, grounding: separate ground contact to mating connector shell and front panel, vertical PCB mount, https://www.neutrik.com/en/product/nc3maav A Series, 3 pole female XLR receptacle, grounding: without ground/shell contact, vertical PCB mount, asymmetric push, https://www.neutrik.com/en/product/nc5fav-da A Series, 5 pole male XLR receptacle, grounding: separate ground contact to mating connector shell and front panel, steel retention lug, horizontal PCB mount, https://www.neutrik.com/en/product/nc3mbh-0 B Series, 3 pole female XLR receptacle, grounding: separate ground contact to mating connector shell and front panel, vertical PCB mount, https://www.neutrik.com/en/product/nc3mav-0 A Series, 3 pole female XLR receptacle, switching contacts, grounding: separate ground contact to mating connector shell and front panel, horizontal PCB mount, https://www.neutrik.com/en/product/nc3mav-0 A Series, 3 pole XLR female receptacle with 6.35mm (1/4in) mono jack, switched, with chrome ferrule and straight PCB pins, https://www.neutrik.com/en/product/nmj6hcd3 M Series, 6.35mm (1/4in) mono jack without switching contact, horizontal PCB mount, retention spring instead of A4 Fireball/Fireball.kicad_pro | 4 .../PCB/precadsr_aux_Gerbers/precadsr-PTH.drl | 99 .../precadsr_aux_Gerbers/precadsr-job.gbrjob | 128 .../PCB/precadsr_Gerbers/precadsr-NPTH.drl | 17 ...estenv_Panel_Dual_Mounting_Holes.kicad_mod | 20 ...Panel_Dual_Slotted_Mounting_Hole.kicad_mod | 35 .../Kosmo_Panel_Mounting_Hole.kicad_mod | 17 .../fastestenv_LED_Hole.kicad_mod | 17 .../PCB/precadsr_Gerbers/precadsr-PTH.drl | 4 .../PCB/precadsr_Gerbers/precadsr-F_SilkS.gbr | 1166 .../PCB/precadsr_Gerbers/precadsr-NPTH.drl | 4 .../precadsr-Edge_Cuts.gbr | 16 Docs/precadsr_bom.md | 45 .../fastestenv_Jack_Hole.kicad_mod | 17 .../fastestenv_Trimmer_Pot_Hole.kicad_mod | 17 .../precadsr_panel_al/precadsr_panel_al.sch | 194 .../precadsr_panel_al-B_SilkS.gbr | 472 aoKicad | 2 Hardware/lib/Kosmo_panel | 1 | SW_DPDT_x2 | Switch, single pole double throw, separate symbols Quad Low-Noise JFET-Input Operational Amplifiers, DIP-8/SOIC-8/TO-99-8"/>