Labels Milestones
BackVertex 8.29927 -3.47343 3.82299 vertex 8.35972 -3.66179 3.76384 facet normal 0.241723 -0.796854 0.553709 facet normal -0.29705 0.243786 0.923217 vertex 8.26214 3.54289 3.82299 facet normal 1.122750e-06 -1.000000e+00 -4.868587e-07 facet normal -0.768482 -0.630652 0.108225 facet normal 0.878606 0.0865364 0.469642 vertex -8.71606 -1.73373 5.07603 facet normal 2.845767e-001 4.980093e-001 8.191476e-001 vertex -2.548207e+000 -4.537391e+000 2.491820e+001 facet normal -3.562743e-001 6.107892e-001 7.071105e-001 vertex 2.607374e+000 -4.475854e+000 2.488700e+001 facet normal 1.304253e-001 -2.235980e-001 9.659157e-001 facet normal 0.560077 0.682457 0.469645 vertex -4.93725 7.38912 5.07603 facet normal 0.766709 -0.634273 0.099275 vertex 7.28969 6.84547 0 facet normal 4.784231e-001 8.781294e-001 0.000000e+000 vertex 5.258615e+000 -2.174272e+000 2.496000e+001 vertex 4.884630e+000 -2.925793e+000 1.747200e+001 facet normal -0.499981 -0.866036 -2.49143e-05 facet normal 0.423073 0.690391 0.58683 facet normal 0.630746 -0.768414 0.108161 facet normal 5.008889e-002 -8.468474e-002 9.951480e-001 facet normal 0.312847 -0.468207 -0.826383 vertex -2.24521 -2.24521 18.7502 facet normal -0.3389 -0.181148 0.923218 vertex 7.87793 4.26169 3.82299 facet normal 0.301372 -0.0723665 0.950757 facet normal 4.268660e-001 7.465647e-001 5.103201e-001 vertex -4.032579e+000 -2.395187e+000 2.482134e+001 facet normal 0.187658 -0.0572764 0.980563 facet normal 0.768773 0.630299 0.108219 facet normal -0.479705 -0.847857 0.225879 vertex -5.7853 4.29641 7.81019 facet normal 0.0624745 -0.0761286 0.995139 facet normal -1.011997e-14 5.429241e-15 -1.000000e+00 d8eca8dc7e Go to file 53c46eece1 Still trying to implement chaining Checkpoint before trying to fit two mounting posts into hole_top = out_row_1 + 94; // this one is easy hole_bottom = hole_top - 90; DivotRadius = KnobMinorRadius*.4; // Primary knob cylinder for (i=[0 : Knurls-1] rotate([0, 0, 45] cube([2, 2, KnobHeight+.001], center=true); if (Pointer2==1 cube([8, 3, KnobHeight], center=true); // Pointer1: Offset hemispherical divot sphere(r=DivotRadius, $fn=40); // Divot1: Centered cylynrical divot // Hole for setscrew } // draws two walls in parallel, close together so a PCB can fit between // h = how thick to make fitting inside a case easier. Or 10mm if it faces away and so on. Use