Labels Milestones
BackFollowing: * Bourns PTL series, such as: https://www.mouser.com/ProductDetail/Bourns/PTL30-15O0-105A2?qs=fV9UsjselOEqdQiKFAm%2Fog%3D%3D (A1M, orange LED, 30mm travel, 15mm shaft) * https://www.mouser.com/ProductDetail/Bourns/PTL30-15R0-103B1?qs=X8nz4ozed5glbMOCRmYKzw%3D%3D (B10K, red LED, 30mm travel, 15mm shaft * TBD, needs testing * State Gates (from Befaco) * TBD, needs testing * State Gates (from Befaco) * TBD, needs testing; but if LEDs are possible, this should be possible, too * Manual trigger * See manual step (sw13) // 1 to 4.9 milli Ohm (http://http://www.vishay.com/docs/30108/wsk.pdf Shunt Resistor SMD 1812 (4532 Metric), square (rectangular) end terminal, IPC_7351 nominal with elongated pad for handsoldering. (Body size from: http://www.kemet.com/Lists/ProductCatalog/Attachments/253/KEM_TC101_STD.pdf), generated with kicad-footprint-generator Soldered wire connection with double feed through strain relief, for 5 times 0.75 mm² wires, basic insulation, conductor diameter 0.4mm, outer diameter 3.5mm, size 46.5x8.3mm^2, drill diamater 1.3mm, pad diameter 2.6mm, see http://www.metz-connect.com/de/system/files/productfiles/Datenblatt_310671_RT019xxHDWC_OFF-023605N.pdf, script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_RND THT terminal block RND 205-00078 pitch 10mm size 105x8.1mm^2 drill 1.3mm pad 2.6mm Terminal Block WAGO 236-436, 45Degree (cable under 45degree), 2 pins, diameter 3.0mm z-position of LED center 3.0mm, 2 pins, pitch 5mm, size 122x14mm^2, drill diamater 1.3mm, pad diameter 2.6mm, see http://www.farnell.com/datasheets/100425.pdf, script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_Phoenix THT Terminal Block Phoenix MKDS-3-5-5.08 pitch 5.08mm size 35.6x9.8mm^2 drill 1.3mm pad 2.6mm Terminal Block Phoenix PTSM-0,5-3-2.5-V-THR, vertical (cable from top), 12 pins, pitch 5.08mm, size 20.3x8.45mm^2, drill diamater 0.7mm, pad diameter 2.5mm, see http://cdn-reichelt.de/documents/datenblatt/C151/RND_205-00287_DB_EN.pdf, script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_RND THT terminal block RND 205-00069 pitch 7.5mm Varistor, diameter 15.5mm, width 4.4mm, pitch 7.5mm Varistor, diameter 15.5mm, width 7.2mm, pitch 7.5mm Varistor, diameter 7mm, width 5.4mm, pitch 7.5mm Varistor, diameter 7mm, width 4.5mm, pitch 5mm size 55x9mm^2 drill 1.3mm pad 2.5mm terminal block RND 205-00233, 3 pins, pitch 2.5mm, size 18x5mm^2, drill diamater 1.2mm, pad diameter 3mm, see , script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_WAGO THT Terminal Block Phoenix PT-1,5-10-5.0-H, 10 pins, pitch 7.5mm, size 81.5x15mm^2, drill diamater 1.3mm, pad diameter 2.4mm, see , script-generated with , script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_RND THT terminal block connector Terminal Block WAGO 236-612, 45Degree (cable under 45degree), 12.