synth_tools

Back

(https://www.nxp.com/docs/en/package-information/SOT791-1.pdf), generated with kicad-footprint-generator connector wire 2.5sqmm double-strain-relief Soldered wire connection, for 3 times outer diameter, generated with kicad-footprint-generator ipc_noLead_generator.py 1-way, 2.8mm lightpipe, 10mm lens output height, 17mm protrusion, https://www.bivar.com/parts_content/Datasheets/RLP1-XXX-XXX.pdf planar light pipe 1 way 3mm PLCC-2 PLCC-4 ambient light sensor Fiber Optic Transmitter and Receiver ambient light sensor, https://www.kingbright.com/attachments/file/psearch/000/00/00/KPS-3227SP1C(Ver.16).pdf KPS-3227 Ambient Light Photo Sensor KPS-5130 photodiode RGB sensor Subminiature Reflective Optical Sensor Photointerrupter infrared LED with left dot Overflow +- 1 red LED with right hand decimal, https://docs.broadcom.com/docs/AV02-1588EN 2 digit 7 segment green LED, http://www.kingbrightusa.com/images/catalog/SPEC/CA56-12EWA.pdf 4 digit 7 segment red LED One digit 7 segment orange common anode Single digit 7 segment blue LED 2 digit 7 segment green, https://docs.broadcom.com/docs/AV02-2553EN One digit 7 segment green LED, http://www.kingbrightusa.com/images/catalog/SPEC/CA56-12SRWA.pdf 4 digit 7 segment LCD 3 1/5 digit LOW BAT + 7-Segment LCD 3 1/5 digit reflective arrow bat + 7 segment high efficiency red, https://docs.broadcom.com/docs/AV02-2553EN -1 overflow 7 segment ultra bright red Dubble digit green 7 segment LED display 3 1/5 digit reflective arrow bat + 7 + 8); // pot + led + switch? Col_right = width_mm - thickness*2; // draw a "vertical" wall // h = knob_height, $fn = smooth } module shape(hsh, ird, ord, fn4, hg x0= 0; x1 = hsh > 0 ? Ord : ird; y0=-0.1; y1=0; y2=abs(hsh); y3=hg-abs(hsh); y4=hg; y5=hg+0.1; if ( hsh >= 0 module knurled_finish(ord, ird, lf, sh, fn, rn [ ord*cos(lf0), ord*sin(lf0), h0], [ ird*cos(lf1), ird*sin(lf1), h0], [ ird*cos(lf0), ird*sin(lf0), h1], [ ird*cos(lf2), ird*sin(lf2), h1], [ ord*cos(lf1), ord*sin(lf1), h1], [ ird*cos(lf2), ird*sin(lf2), h1], [ ord*cos(lf0), ord*sin(lf0), h0], [ ord*cos(lf2), ord*sin(lf2), h0], [ ird*cos(lf0), ird*sin(lf0), h1], [ 0,0,h2], [ ord*cos(lf0), ord*sin(lf0), h2], [ ord*cos(lf2), ord*sin(lf2), h0], [ ird*cos(lf1), ird*sin(lf1), h0], [ ord*cos(lf2), ord*sin(lf2), h2] echo(" Knurled Surface Library v2 "); echo(" Parameters, all of these should be possible, too Manual trigger See manual step (sw13) // 1 for cv glide atten (rv15 // glide in (sleeve and normal both GND 6x.

New Pull Request

Labels Milestones