synth_tools

Back

8-pin SOT-23 package, Handsoldering, http://www.analog.com/media/en/package-pcb-resources/package/pkg_pdf/sot-23rj/rj_8.pdf SOT-143R, reverse pinning, https://www.nxp.com/docs/en/package-information/SOT143R.pdf SOT-143R, reverse pinning, https://www.nxp.com/docs/en/package-information/SOT143R.pdf SOT-143R, reverse pinning, https://www.nxp.com/docs/en/package-information/SOT143R.pdf SOT-143R, reverse pinning, https://www.nxp.com/docs/en/package-information/SOT143R.pdf SOT-143R, reverse pinning, https://www.nxp.com/docs/en/package-information/SOT143R.pdf SOT-143R, reverse pinning, https://www.nxp.com/docs/en/package-information/SOT143R.pdf SOT-143R, reverse pinning, Handsoldering, https://www.nxp.com/docs/en/package-information/SOT143R.pdf module CMS SOT223 4 pins for trigger, gate, and CV routing # Precision ADSR with retriggering and looping modifications * Bourns PTL series, such as: ** https://www.mouser.com/ProductDetail/Bourns/PTL30-15O0-105A2?qs=fV9UsjselOEqdQiKFAm%2Fog%3D%3D (A1M, orange LED, 30mm travel, 15mm shaft * TBD, needs testing; but if LEDs are possible, this should be possible, too * Manual trigger See manual step (sw13) - pushbutton // glide in (sleeve and normal both GND 6x Sockets, 2pin: - all step switches (all go to same bus run/stop 2x Pushbutton switches, all 2pin: - reset Pots, 3-pin: - Glide In - diode to U2-3 - Clock POT is the two clockwise-most pins, looking from below. Clock rate (B100k) (not sure yet which 2 pins Rectangular size 3.3x2.4mm^2 diameter 1.8mm size 1.8x2.4mm^2 z-position of LED center 2.0mm, 2 pins, Rectangular size 5.0x2.0mm^2 z-position of LED center 1.0mm 2 pins diameter 3.0mm z-position of LED center 3.0mm 2 pins diameter 5.0mm z-position of LED center 1.0mm 2 pins LED diameter 3.0mm width 1.6mm Capacitor C, Rect series, Radial, pin pitch=2.00mm, diameter=5mm, height=11mm, Non-Polar Electrolytic Capacitor C, Rect series, Radial, pin pitch=5.00mm, , diameter=12.0mm, Fastron, 11P, http://cdn-reichelt.de/documents/datenblatt/B400/DS_11P.pdf Inductor Radial series Radial pin pitch 5.08mm size 66x11.2mm^2 drill 1.3mm pad 2.5mm terminal block RND 205-00062, 45Degree (cable under 45degree), 16 pins, pitch 7.5mm, size 45x10.3mm^2, drill diamater 1.15mm, pad diameter 2.4mm, see , script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_Phoenix THT Terminal Block Phoenix PT-1,5-9-3.5-H pitch 3.5mm size 18.2x7mm^2 drill 1.2mm pad 2mm PhoenixContact PTSM0,5 2 HV 2,5mm vertical SMD spring clamp terminal block Metz Connect Type205_RT04506UBLC 45Degree pitch 5mm Varistor, diameter 21.5mm, width 5mm, pitch 10mm size 105x8.1mm^2 drill 1.3mm pad 2.5mm terminal block RND 205-00018, 8 pins, pitch 2.54mm, size 25.86x6.5mm^2, drill diamater.

New Pull Request

Labels Milestones