Labels Milestones
BackLED 3.2x2.7mm http://www.avagotech.com/docs/AV02-0610EN LED RGB Wurth PLCC-4 LED RGB NeoPixel Mini 'Piranha' RGB LED, SMD, PLCC-2, 3.0 x 2.0mm, orientation marker at cathode, https://optoelectronics.liteon.com/upload/download/DS22-2009-0099/LTW-M670ZVS-M5_0906.pdf LED RGB APFA3010 KINGBRIGHT 3x1.5mm Dual LED SMD 3mm Right Angle Low-profile vertical USB Micro-B receptacle, http://www.mouser.com/ds/2/445/629105150521-469306.pdf USB Mini-B 5-pin SMD connector, http://downloads.lumberg.com/datenblaetter/en/2486_01.pdf USB USB_B USB_Mini connector usb mini receptacle vertical Hirose DF12C SMD, DF12C3.0-20DS-0.5V, 20 Pins per row (http://suddendocs.samtec.com/prints/hle-1xx-02-xx-dv-xe-xx-mkt.pdf, http://suddendocs.samtec.com/prints/hle-thru.pdf), generated with kicad-footprint-generator Harting har-flexicon series connector, 14110813001xxx (https://b2b.harting.com/files/download/PRD/PDF_TS/1411XX13001XXX_100228421DRW046C.pdf), generated with kicad-footprint-generator ipc_noLead_generator.py QFN, 64 Pin (http://ww1.microchip.com/downloads/en/DeviceDoc/64L_VQFN_8x8_with%206_5x6_5%20EP_JXX_C04-0437A.pdf), generated with kicad-footprint-generator Mounting Hardware, inside through hole M3, height 8, Wuerth electronics 9774015633 (https://katalog.we-online.com/em/datasheet/9774015633.pdf), generated with kicad-footprint-generator Samtec HLE .100" Tiger Beam Cost-effective Single Beam Socket Strip, HLE-109-02-xxx-DV-LC, 9 Pins per row (https://www.hirose.com/product/en/products/DF63/), generated with kicad-footprint-generator Soldered wire connection, for a little wiggle room on the same size as traces - .3mm for non-power lines, .6mm if carrying power - MK uses a ground plane. - when pressed, short +12V and Reset In socket - Reset Sw - when pressed, short +12V and Reset In - U1-13 (can get at from top when assembled - Stop Switch - 10 LEDs 3 sockets 6 sockets Potentiometers: One potentiometer for internal clock rate. One SPDT switch to disable reset (run once). - Momentary-normal-off pushbutton to manually step. - SPST switch per step, to indicate current step. (10 Momentary-normal-off pushbutton to manually reset. LEDs: One per step, to set output voltages. (10) One potentiometer for internal clock signal (possibly external). Commonly called a "Baby 8". Final tweaks, version submitted to JLCPCB on 20240124 v1.0 Add CV in complex ways. - CV Range - Once/Cont 11 Toggle Switches, 3pin: 11 Toggle Switches, 2pin: - all step switches (all go to same bus 2x Pushbutton switches, all 2pin: - reset Pots, 3-pin: - Glide attenuator (B10k) (join two left pins from below Pots, 2-pin: - Glide, manual (A100k) (two left pins, from below Clock rate goes down when resistance goes up, opposite to expectation. C1 is too small; need more than 100k to get below 200bpm~ 3D Printing/6u_wing_v1.scad rename to 3D Printing/Cases/6u_wing_v1.scad 3D Printing/Rails/18hp_innie.stl Normal file Unescape Period.
New Pull Request