synth_tools

Back

14mm Electrolytic Capacitor CP, Radial_Tantal series, Radial, pin pitch=5.00mm 7.50mm, , diameter=10mm, Electrolytic Capacitor CP, Axial series, Axial, Horizontal, pin pitch=5.08mm, , length*diameter=9.5*4mm^2, Fastron, SMCC, http://cdn-reichelt.de/documents/datenblatt/B400/DS_SMCC_NEU.pdf, http://cdn-reichelt.de/documents/datenblatt/B400/LEADEDINDUCTORS.pdf Inductor Axial series Axial Vertical pin pitch 30mm length 25mm width 9mm height 9mm Resistor, Axial_Power series, Box, pin pitch=25.4mm, 1.5W, length*diameter=14.3*5.7mm^2 Resistor Axial_DIN0614 series Axial Horizontal pin pitch 5.08mm size 50.8x9.8mm^2 drill 1.3mm pad 2.6mm Terminal Block Phoenix PT-1,5-11-3.5-H, 11 pins, pitch 7.5mm, size 15x10.3mm^2, drill diamater 1.3mm, pad diameter 2.6mm, see http://www.farnell.com/datasheets/2138224.pdf, script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_RND THT terminal block connector Terminal Block WAGO 804-308 45Degree pitch 7.5mm size 22.5x9mm^2 drill 1.3mm pad 2.5mm terminal block Metz Connect Type067_RT01905HDWC pitch 10mm Varistor, diameter 9mm, width 4.8mm, pitch 10mm size 242x14mm^2 drill 1.15mm pad 3mm Terminal Block Phoenix MKDS-1,5-7, 7 pins, pitch 5mm, size 72.3x14mm^2, drill diamater 1.3mm, pad diameter 2.6mm, see http://www.farnell.com/datasheets/100425.pdf, script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_WAGO THT Terminal Block WAGO 804-306, 45Degree (cable under 45degree), 6 pins, pitch 5mm, size 12.3x14mm^2, drill diamater 1.3mm, pad diameter 3mm, size source Multi-Contact FLEXI-xV 2.0 (https://ec.staubli.com/AcroFiles/Catalogues/TM_Cab-Main-11014119_(en)_hi.pdf), bend radius 3 times 0.75 mm² wires, reinforced insulation, conductor diameter 1.4mm, outer diameter 2.7mm, size source Multi-Contact FLEXI-xV 2.5 (https://ec.staubli.com/AcroFiles/Catalogues/TM_Cab-Main-11014119_(en)_hi.pdf), bend radius 3 times outer diameter, generated with kicad-footprint-generator ipc_noLead_generator.py NXP LGA, 8 Pin (https://www.ti.com/lit/ds/symlink/lp2987.pdf#page=26), generated with kicad-footprint-generator JST XA series connector, 14111113002xxx (https://b2b.harting.com/files/download/PRD/PDF_TS/1411XX13002XXX_100228421DRW035C.pdf), generated with kicad-footprint-generator ipc_noLead_generator.py GPS Module, 15.5x15.5x6.3mm, https://www.u-blox.com/sites/default/files/SAM-M8Q_HardwareIntegrationManual_%28UBX-16018358%29.pdf GPS GNSS ublox ZED GSM NB-IoT module BC95 Quad-Band GSM/GPRS module, 24x24x3mm, http://simcom.ee/documents/SIM900/SIM900_Hardware%20Design_V2.05.pdf Telit xL865 familly footprint, http://www.telit.com/fileadmin/user_upload/products/Downloads/3G/Telit_UL865_Hardware_User_Guide_r8.pdf ublox Sara GSM/HSPA modem, https://www.u-blox.com/sites/default/files/SARA-G3-U2_SysIntegrManual_%28UBX-13000995%29.pdf, pag.162 ublox SARA-G3 SARA-U2 GSM HSPA Footprint for Mini-Circuits case MMM168, Land pattern PL-094, pads 5 and 6 // manual reset (sw16 // 8 Sockets: // clock in (j2/j11 // casc out (j14/j15 // reset/casc in (j1/j13 // gate out (j4/j10) // clock out (j5/j12 // glide in (sleeve and normal both GND Glide attenuator (B10k) (join two left pins from below Clock POT is too small for film; is film needed? More notes C10, C14 too small for film; is film needed? Notes: Could make the bodging of the reverse. See Make Noise's.

New Pull Request

Labels Milestones