synth_tools

Back

PentawattF-, MultiwattF-5, staggered type-2 TO-220F-9, Vertical, RM 2.54mm, staggered type-1 TO-220-5, Horizontal, RM 2.54mm TO-251-2, Horizontal, RM 5.475mm, SOT-93, see https://www.vishay.com/docs/95214/fto218.pdf TO-218-2 Horizontal RM 4.58mm IPAK TO-251-3, Horizontal, RM 1.27mm, MultiwattF-15, staggered type-1 TO-220F-11, Vertical, RM 1.7mm, staggered type-1, see http://www.ti.com/lit/ds/symlink/lm3886.pdf TO-220F-11 Vertical RM 2.54mm staggered type-2 TO-220-4 Vertical RM 1.7mm Pentawatt Multiwatt-5 staggered type-1 TO-220-4 Vertical RM 0.9mm staggered type-2 TO-220F-4, Vertical, RM 2.54mm, staggered type-1 TO-220-8 (Multiwatt8), Vertical, 2.54mm Pitch Multiwatt 8 TO-220-9, Vertical, RM 2.54mm TO-220-4 Horizontal RM 2.54mm staggered type-2 TO-220-9 Vertical RM 2.54mm TO-220-4, Vertical, RM 0.97mm, Multiwatt-9, staggered type-1 TO-220F-11, Vertical, RM 2.54mm, staggered type-2 TO-220F-7, Vertical, RM 2.54mm, see https://www.vishay.com/docs/66542/to-220-1.pdf TO-220-3 Vertical RM 5.45mm TO-3P-3, Vertical, RM 3.81mm, see https://www.onsemi.com/pub/Collateral/NJL3281D-D.PDF TO-264-5 Vertical RM 1.27mm staggered type-1 TO-220-5, Vertical, RM 5.45mm, , see http://www.onsemi.com/pub/Collateral/340AC.PDF TO-3PB-3 Vertical RM 4.58mm IPAK TO-251-2, Vertical, RM 4.58mm, IPAK, see https://www.diodes.com/assets/Package-Files/TO251.pdf TO-251-3 Horizontal RM 2.54mm TO-251-2, Horizontal, RM 2.286mm SIPAK Vertical RM 1.7mm MultiwattF-11 staggered type-1 TO-220-11, Horizontal, RM 2.286mm Plastic near cylindrical package Sod-70 see: https://www.nxp.com/docs/en/data-sheet/KTY81_SER.pdf [StepUp generated footprint] SOT-227 / SOT-227B / ISOTOP, M4 mounting hole 2.2mm m2 iso14580 Mounting Hole 2.2mm, no annular, M5, ISO14580 mounting hole 6.4mm no annular mounting hole 2.7mm no annular mounting hole 4mm no annular Mounting Hole 2.2mm, M2, DIN965 mounting hole 3.2mm no annular Mounting Hole 2.7mm, M2.5, DIN965 mounting hole 2.2mm m2 iso14580 Mounting Hole 6mm, no annular mounting hole position tweaks f6c7924538 Messing around with panel title fonts More experimentation with panel alignment before printing 9a2ab6dc7f initial notes for v1 build - C1 is too small for film; is film needed? Notes: Could make the clock oscillilator an external CV-to-pulse-rate module? Is this even useful? Seven-segment display. Can be done, but requires a lot of wiring and increases risk of noise on power rails. Things best left to external modules: - CV-controlled CV offset module - add a voltage to trigger steps. Replace C10 with 100K resistor.

New Pull Request

Labels Milestones