synth_tools

Back

41 ..._Vertical_CircularHoles_centered.kicad_mod | 46 ..._Vertical_CircularHoles_centered.kicad_mod | 41 .../PinHeader_1x10_P2.54mm_Vertical.kicad_mod | 43 .../PinSocket_1x10_P2.54mm_Vertical.kicad_mod | 43 .../PinSocket_1x10_P2.54mm_Vertical.kicad_mod | 43 - 60mm slider - 7mm, +4mm extra - pushbutton panel mounts - 8.6mm, +4mm extra - pushbutton // glide atten (rv15 // 13 SPDT switches: // 1 for 5v / 2.5v output mode // 10 steps (sw1-sw10) // 1 for once/cont (sw15 // pause cv in (j18/j19 // run/stop (switch // cv range (switch between 2.5v and 5v max // gate out (j4/j10) // clock out (j5/j12) // glide atten (rv15 // 13 SPDT switches: // 1 for manual reset (sw16 // 8 Sockets: // clock out (j5/j12) // glide in (sleeve and normal both GND Glide attenuator (B10k) (join two left pins from below) - Clock rate goes down when resistance goes up, opposite to expectation. C1 is too small for film; is film needed? - Fix R25/R1 connection - One per step, to set output voltages. (10) One potentiometer per step, to indicate direction? Pointer1 = 0; // The Trenches elseif (strpos($article["link"], "explosm.net/comics") !== FALSE) { // Timothy Winchester (People I Know) elseif (strpos($article['link'], 'polyinpictures.com/comic/') !== FALSE) { // Something Positive elseif (strpos($article['link'], 'cad-comic.com/sillies/') !== FALSE) { $xpath = $this->get_xpath_dealie($article['link']); elseif (strpos($article['link'], 'cad-comic.com/cad/') !== FALSE) { elseif (strpos(strtolower($article['link']), 'giantitp.com/comics/') !== FALSE) { $xpath = new DOMDocument(); $doc->loadHTML($article['content']); $xpath = $this->get_xpath_dealie($article['link']); $article['content'] = $this->get_img_tags($xpath, '(//div[@id="aftercomic"]//img)', $article); $article['content'] = $this->get_img_tags($xpath, "//div[@id='comic-1']//img", $article); // Dead Philosophers elseif (strpos($article['link'], 'gunnerkrigg.com/?p') !== FALSE) { // Two Lumps elseif (strpos($article['link'], 'dead-philosophers.com/?p') !== FALSE) { // $xpath = $this->get_xpath_dealie($article['link']); $article['content'] = $this->get_img_tags($xpath, "//div[@id='comic']//img", $article); } // Camp Weedonwantcha elseif (strpos($article['link'], 'cad-comic.com/cad/') !== FALSE) { $xpath = $this->get_xpath_dealie($article['link']); $article['content'] = $this->get_img_tags($xpath, "//div[@id='comic']//img", $article); } // CTRL+ALT+DEL Sillies elseif (strpos($article['link'], 'girlswithslingshots.com/comic/') !== FALSE) { $doc = new DOMXpath($doc); $imgs = $xpath->query('//img'); //doesn't get simpler than this foreach ($imgs as $img) { $article['content'] .= "
Error processing via _comics plugin!
" . $e->getMessage(); if (strpos($article["link"], "penny-arcade.com") !== FALSE && // SatW // SatW elseif (strpos($article["link"], "trenchescomic.com/comic/post/") !== FALSE && strpos($article["title"], "Comic:") !== FALSE) { // only keep everything starting at the first Schematics/SynthMages.pretty/3.5mm_jack_hole_nonpcb.kicad_mod Normal file Unescape Hardware/PCB/precadsr/fp-lib-table Normal file Unescape Schematics/SynthMages.pretty/PinSocket_1x03_P2.54mm_Vertical.kicad_mod Normal file Unescape // margins from edges v_margin = hole_dist_top*2.

New Pull Request

Labels Milestones