Labels Milestones
BackType, from the side echo("offsetToMountHoleCenterY: ", offsetToMountHoleCenterX); module eurorackMountHoles(php, holes, hw) { holes = holes-holes%2;//mountHoles ought to be manipulated. Detail level is a ceramic 104 power cap like C5, C6, C8, C9 | 4 Schematics/Unseen Servant/Unseen Servant.kicad_pcb | 31887 .../Unseen Servant/Unseen Servant.kicad_sch | 26 ...D_DO-35_SOD27_P7.62mm_Horizontal.kicad_mod | 51 create mode 100644 MIXER.diy create mode 100644 Hardware/PCB/precadsr/ao_tht.pretty/CP_Radial_D5.0mm_P2.00mm.kicad_mod delete mode 100644 Panels/FireballSpellVertVerySmall.png create mode 100644 Hardware/PCB/precadsr/Kosmo_panel.pretty/Kosmo_Jack_Hole.kicad_mod create mode 100644 Hardware/PCB/precadsr/Kosmo_panel.pretty/Kosmo_LED_Hole_NPTH.kicad_mod create mode 100644 Hardware/PCB/precadsr/ao_tht.pretty/TO-92_Inline_Wide.kicad_mod create mode 100644 Hardware/PCB/precadsr_Gerbers/precadsr-F_Cu.gbr create mode 100644 Hardware/PCB/precadsr/Kosmo_panel.pretty/Kosmo_Pot_Hole_NPTH.kicad_mod create mode 100644 Schematics/SynthMages.pretty/SOCKET_3_PIN_HEADER_NORMAL.kicad_mod From 5663c8bc865b744661cf82b1abfca64d73c0f2fa Mon Sep 17 00:00:00 2001 .../Panels/PRISMATIC SPHERE.png | Bin 0 -> 11930 bytes create mode 100644 Hardware/Panel/precadsr-panel-Gerbers/precadsr-panel-CuBottom.gbl create mode 100644 Hardware/PCB/precadsr/ao_tht.pretty/SOT-23_Handsoldering.kicad_mod create mode 100644 Schematics/Luthers_Perfboard.pdf From dd8c61c34faaeb27b8a193b7a0410df7bb5b6b87 Mon Sep 17 00:00:00 2001 Subject: [PATCH] Add notes about UX component wiring 2x Sockets, all three pins need wires: glide in (sleeve and normal both GND - Gate out (could normal to Reset In socket - Reset Socket to U3-3 = capacitor measurement roughly 15nF (has a resistor limiting max drone frequency:
re-re-remove the mysterious extra trace Binary files a/Docs/precadsr.pdf and b/Docs/precadsr.pdf differ Binary files /dev/null and b/Images/IMG_6753.JPG differ Binary files /dev/null and b/Panels/futura light bt.ttf differ From 2537badf2888da8d57706bf8be36ba8f10d4993a Mon Sep 17 00:00:00 2001 Subject: [PATCH 10/13] glide fix glide fix Notes from debugging Clock POT is too small; need more than 100k to get below 200bpm~ 3D Printing/6u_wing_v1.scad → 3D Printing/Cases/6u_wing_v1.scad Binary files /dev/null and b/Synth_Manuals/LABOR_MANUAL.pdf differ Binary files a/3D Printing/Panels/MAGIC MISSILE VCF.png' Delete '3D Printing/AD&D 1e spell names in Filmoscope Quentin/Panels' 8de432ba4663cc4e208cff778a114b9ae41e7906 Upload files to '3D Printing/AD&D 1e spell names in Filmoscope Quentin/Panels/MAGIC MISSILE VCF.png' Delete '3D Printing/AD&D 1e spell names in Filmoscope Quentin/Panels/UNSEEN SERVANT.png Normal file View File 3D Printing/Panels/image.png Normal file Unescape Hardware/PCB/precadsr/ao_tht.pretty/Potentiometer_Bourns_3296W_Vertical_screw_centered.kicad_mod Normal file Unescape * Bourns PTL series, such as: * https://www.mouser.com/ProductDetail/Bourns/PTL30-15O0-105A2?qs=fV9UsjselOEqdQiKFAm%2Fog%3D%3D (A1M, orange LED, 30mm travel, 15mm shaft ** https://www.mouser.com/ProductDetail/Bourns/PTL30-15R0-103B1?qs=X8nz4ozed5glbMOCRmYKzw%3D%3D (B10K, red LED, 30mm travel, 15mm shaft * TBD, needs testing * State Gates (from Befaco) TBD, needs testing; but if LEDs are possible, this should be height of the main (cylindrical or.