synth_tools

Back

Clf_indicator_angle_from_notch = 0; right_rib_x = width_mm - col_right + tolerance*4; // column from edge plus hole radius //calculated x value of exact middle of panel after deducting left/right sub-panels slider_center = (width_mm - left_panel_width - right_panel_width)/2 + left_panel_width; slider_bottom = v_margin+8; Panels/10_step_seq_38hp_v1.scad Normal file Unescape Hardware/PCB/precadsr/Kosmo_panel.pretty/Kosmo_Trimmer_Pot_Hole.kicad_mod Normal file View File 3D Printing/Tools/jack-wrench.stl Executable file View File VCO_MANUAL_v2.pdf Executable file View File Datasheets/tl074.pdf Normal file View File Synth_Manuals/Kassutronics_Slope_Build_Docs_2.0A-1.pdf Normal file View File 3D Printing/Pot_Knobs/18-spline-pot-knob-indicator-line.stl Executable file View File Examples/EG_MANUAL.pdf Normal file Unescape REP: repique CAX: caixa MSD: mid surdo (sometimes MS1, MS2, etc, if pattern spans measures or variations) BSD: back surdo (L for low, H for high) R/L: accented note (right/left hand suggested r/l: Quieter, unaccent note *R or *L: Trill this note Delete Page Deleting the wiki page "Samba Reggae 1" cannot be undone. Continue? 5cacbfea2e Add polygon calculation for wing plates 5cacbfea2e523d618ea3bcbc0bca9c37eb36f10d Update README.md Don't put R8 so close to R26 -- D36/R47 too close Testing before powering up: Clock In - U1-13 (can get at from top when assembled - Stop Switch - 10 ohms between U1-14 and U2-1 when off, more like 1M when off - Single Step - 12V through 10k Ohms to U-1-14, more like 1M when off - Glide attenuator (B10k) (join two left pins from below - Glide, manual (A100k) (two left pins, from below Clock rate goes down when resistance goes up, opposite to expectation. C1 is too small for a single 1 mm² wires, basic insulation, conductor diameter 1.4mm, see http://www.metz-connect.com/de/system/files/productfiles/Datenblatt_310861_RT034xxHBLC_OFF-026114K.pdf, script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_WAGO THT Terminal Block TE 282834-5, 5 pins, pitch 2.5mm, size 12.2x10mm^2, drill diamater 1.3mm, pad diameter 2.6mm, see http://www.metz-connect.com/de/system/files/productfiles/Datenblatt_311751_RT027xxHBLC_OFF-022814U.pdf, script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_MetzConnect THT terminal block Metz Connect 360272, block size 5x5mm^2, drill diamater 1.3mm, pad diameter 3mm, see , script-generated with , script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_WAGO THT Terminal Block 4Ucon ItemNo. 20001 pitch 3.5mm size 8x8.3mm^2 drill 1.3mm pad 2.5mm terminal block RND 205-00015 pitch 5mm size 15x8.1mm^2 drill 1.1mm pad 2.1mm Terminal Block WAGO 236-116 45Degree pitch 5mm size 45x9mm^2 drill 1.3mm pad 2.5mm terminal block connector Terminal Block Phoenix PT-1,5-7-3.5-H pitch 3.5mm size 29x8.3mm^2 drill 1.3mm pad 2.6mm Terminal Block Phoenix PTSM-0,5-6-2.5-V-THR, vertical (cable from top), 8 pins, pitch 5.08mm, size 61x9.8mm^2, drill diamater 1.1mm, pad diameter 2.5mm, see http://www.metz-connect.com/de/system/files/productfiles/Datenblatt_311711_RT137xxHBWC_OFF-022811Q.pdf, script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_RND THT terminal.

New Pull Request

Labels Milestones