Labels Milestones
Back55x9mm^2, drill diamater 1.3mm, pad diameter 2.5mm, hole diameter 0.7mm, wire diameter 1.0mm wire loop as test Point, diameter 3.0mm, 2 pins, http://www.kingbright.com/attachments/file/psearch/000/00/00/L-169XCGDK(Ver.9B).pdf LED_Rectangular Rectangular Rectangular size 5.0x2.0mm^2 z-position of LED center 9.0mm 2 pins Rectangular size 5.0x2.0mm^2 z-position of LED center 3.0mm 2 pins LED, diameter 5.0mm 2 pins LED diameter 5.0mm z-position of LED center 3.0mm, 2 pins, pitch 5.08mm, size 10.2x9.8mm^2, drill diamater 1.1mm, pad diameter 3mm, size source Multi-Contact FLEXI-xV 1.0 (https://ec.staubli.com/AcroFiles/Catalogues/TM_Cab-Main-11014119_(en)_hi.pdf), bend radius 3 times outer diameter, generated with kicad-footprint-generator Molex MicroClasp Wire-to-Board System, 55935-0910, with PCB trace layout Checkpoint in case of crashes master ttrss-plugin- _comics/init.php 511 lines label_font_size = 5; //mm center_col = width_mm/2; //mm third_col = 60.7-center_adjust; //mm cv_in = [first_col, third_row, 0]; //Fourth row interface placement sync_in = [first_col, third_row, 0]; fm_in = [h_margin+working_width/8, row_3, 0]; cv_in_2b = [right_col, row_1, 0]; fm_pot = [input_column - h_margin/2, bottom_row, 0]; cv_in = [h_margin, row_1, 0]; square_out = [third_col, fourth_row, 0]; //Fifth row interface placement sync_in = [first_col, third_row, 0]; saw_out = [third_col, fourth_row, 0]; //Fifth row interface placement f_tune = [second_col, fourth_row, 0]; //Fifth row interface placement sync_in = [first_col, first_row, 0]; //Second row interface placement f_tune = [width_mm/2 - h_margin, top_row, 0]; f_tune = [width_mm/2 - h_margin, top_row, 0]; scale([.38,.38,-.005]) surface("FireballSpellVertSmaller.png", center=true, invert=false); } module jackStorageHole(horizontalOffset, verticalOffset, diameter { mountHoleDepth = panelThickness+2; // because diffs need to glue knobs thunkicons: tight, but could also do all-different colors, but unfortunately Mouser only has A1Ms in orange. Replacing LEDs in sliders, lit for each Contribution on the 16-pin IDC connector when nothing is plugged in on the streets of the side echo("offsetToMountHoleCenterY: ", offsetToMountHoleCenterY); echo("offsetToMountHoleCenterY: ", offsetToMountHoleCenterY); echo("offsetToMountHoleCenterY: ", offsetToMountHoleCenterY); echo("offsetToMountHoleCenterY: ", offsetToMountHoleCenterX); module eurorackMountHoles(php, holes, hw holes = holes-holes%2;// mountHoles ought to be +1mm between legs -- Don't put R8 so close to R26 - D36/R47 too close From 812d609d12a788e600a582b2b6e7494f6d2b0728 Mon Sep 17 00:00:00 2001 Subject: [PATCH] Submodules, improved NPTH Hardware/lib/Kosmo_panel | 2 | 1N5817 | Schottky Barrier Rectifier Diode, DO-41"/>