synth_tools

Back

Blue Samurai formatting caixa bits Samurai * https://www.mouser.com/ProductDetail/Bourns/PTL30-15O0-105A2?qs=fV9UsjselOEqdQiKFAm%2Fog%3D%3D (A1M, orange LED, 30mm travel, 15mm shaft * https://www.mouser.com/ProductDetail/Bourns/PTL30-15R0-103B1?qs=X8nz4ozed5glbMOCRmYKzw%3D%3D (B10K, red LED, 30mm travel, 15mm shaft * https://www.mouser.com/ProductDetail/Bourns/PTL30-15R0-103B1?qs=X8nz4ozed5glbMOCRmYKzw%3D%3D (B10K, red LED, 30mm travel, 15mm shaft ** https://www.digikey.com/en/products/detail/bourns-inc/PTL30-15R0-103B1/3781301 (red B10K) and https://www.digikey.com/en/products/detail/bourns-inc/PTL30-15O0-105A2/7314942 (orange A1M *** The first two groups should be fine More distant future Less confident about the lineage in the same form factor, with maybe a little wiggle room on the rails v_wall(h=4, l=height-rail_clearance*2-thickness, th=thickness*1.25); v_wall(h=4, l=height-rail_clearance*2, th=right_rib_thickness); //outline of whole PCB cube([137.5, 97, 1], center=true); echo("Putting a hole with radius: ", hole_r , " at ", hole_dist_side, height - 25; // build up seven rows; middle one unused row_2 = row_1 + vertical_space/7; cv_in_1a = [left_col, row_5, 0]; cv_in_2a = [left_col, row_1, 0]; pwm_in = [width_mm - h_margin - working_width/8, row_4, 0]; pwm_cv_lvl = [second_col, fifth_row, 0]; pwm_duty = [second_col, third_row, 0]; fm_lvl = [h_margin+working_width/8, row_3, 0]; c_tune = [width_mm/2 + h_margin, top_row, 0]; left_rib_x = 0; // [0:No, 1:Yes] ////////////////////////// //Advanced settings ////////////////////////// RingThickness = 5*1; DivotDepth = 1.5*1; DistanceBetweenKnurls = 3*1; TimerKnobConst = 1.8*1; PI=3.14159265*1; KnobMajorRadius = KnobDiameter/2; KnobMinorRadius = KnobDiameter/2 * (1 - TaperPercentage/100); KnobRadius = KnobMinorRadius + (KnobMajorRadius-KnobMinorRadius)/2; Divot=CapType; TaperAngle=asin(KnobHeight / (sqrt(pow(KnobHeight, 2) cube([2, 2, KnobHeight+.001], center=true); if (Pointer2==1 cube([8, 3, KnobHeight], center=true); // Pointer1: Offset hemispherical divot sphere(r=DivotRadius, $fn=40); // Divot1: Centered cylynrical divot // Hole for setscrew // Make sure bottom ends at z=0 © 2012 Steve Cooley ( http://sc-fa.com , http://beatseqr.com , http://hapticsynapses.com © 2021 Matthias Ansorg ( https://ma.juii.net A.

New Pull Request

Labels Milestones