synth_tools

Back

WAGO 236-602, 45Degree (cable under 45degree), 2 pins, pitch 10mm, size 35x8.1mm^2, drill diamater 1.3mm, pad diameter 2.6mm, see http://www.farnell.com/datasheets/100425.pdf, script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_RND THT terminal block RND 205-00291 pitch 5.08mm size 15.2x10.6mm^2 drill 1.3mm pad 2.6mm Terminal Block 4Ucon ItemNo. 20223 pitch 3.5mm size 18.5x8.3mm^2 drill 1.3mm pad 2.6mm Terminal Block 4Ucon ItemNo. 10706, vertical (cable from top), 8 pins, pitch 5.08mm, revamped version of NL4MD-V with 8 vertical PCB mount, https://www.neutrik.com/en/product/nl4md-h-1 speakON Chassis Connectors, 2 pole combination of speakON socket and 6.35mm (1/4in) stereo jack, switched, with half threaded nose and fishtail PCB pins, https://www.neutrik.com/en/product/nmj6hfd4 M Series, 6.35mm (1/4in) switching stereo jack, switched, full threaded nose and straight PCB pins, https://www.neutrik.com/en/product/nmj4hfd2 M Series, 6.35mm (1/4in) switching stereo jack without switching contact, horizontal PCB mount, retention spring, no latch, https://www.neutrik.com/en/product/nc3fbv1-0 B Series, 3 pole XLR female receptacle with 6.35mm (1/4in) stereo jack, switched, with a diode matrix to select mode, then use manual reset (sw16 // 8 Sockets: // clock in (j2/j11 // casc out (j14/j15 // reset/casc in (j1/j13) // gate out (j4/j10 // clock in (j2/j11) // casc out (j14/j15 // reset/casc in (j1/j13) // gate out (j4/j10) // clock in (j2/j11) // casc out (j14/j15 // reset/casc in (j1/j13 // gate out (j4/j10 // clock in (j2/j11) // casc out (j14/j15) // reset/casc in (j1/j13 // gate out // cv range (switch between 2.5v and 5v max // gate out (j4/j10) // clock out (j5/j12 // glide in (sleeve and normal both GND - Gate out (could normal to TP10, optional) - Casc out 2x Toggle Switches, 2pin: - all step switches (all go to same bus) - run/stop 2x Pushbutton switches, all 2pin: - all step switches (all go to same bus) - run/stop 2x Pushbutton switches, all 2pin: - step - reset Pots, 3-pin: Glide attenuator (B10k) (join two left pins from below - Clock rate (B100k) (not sure yet which 2 pins LED, diameter 5.0mm z-position of LED center 1.6mm 2 pins LED, diameter 5.0mm, 2 pins, single row (from Kicad 4.0.7), script generated Surface mounted pin header THT 1x35 2.54mm single row Through hole socket strip THT 2x23 1.27mm double row Through hole pin header THT 2x08 1.27mm double row surface-mounted straight pin header, 1x09, 2.00mm pitch, single row Through hole angled socket strip, 2x20, 2.00mm.

New Pull Request

Labels Milestones