synth_tools

Back

3.90 mm Body [QFN] with corner pads and trace routing to de-bodge the pots. D5bfb6e27b 's notes on updating the fireball for rev 2 Battery clip for batteries with a hair of margin // margins from edges v_margin = hole_dist_top*2 + thickness; v_margin = hole_dist_top*5; output_column = width_mm - hole_dist_side - thickness; module label(string, size=4, halign="center") { PSU/Synth Mages Power Word Stun.kicad_prl | 77 Synth Mages Power Word Stun.kicad_pcb 23480 lines general (thickness 1.6) paper "A4") updates to rev 2 beta README.md | 29 .../ao_tht.pretty/LED_D5.0mm.kicad_mod | 34 ...0D_Single_Vertical_CircularHoles.kicad_mod | 46 Hardware/PCB/precadsr/sym-lib-table | 2 pin Molex connector 2.54 mm spacing | | | R15, R17, R19 | 3 | 22k | Resistor | | | J3 | 1 | 1 | B10k | Potentiometer | | | | | ----- | --- | ---- | ---- | ---- | ---- | ----------- | ---- | ----------- | ---- | ----------- | ---- | | U3 | 1 | TL074 | Quad Low-Noise JFET-Input Operational Amplifiers, DIP-14/SOIC-14 Low-Power, Dual Operational Amplifiers, DIP-8/SOIC-8/TSSOP-8/VSSOP-8 Binary files /dev/null and b/3D Printing/Panels/Radio_shaek_standoff_thick.stl differ Binary files /dev/null and b/Panels/label_test.stl differ surface("FireballSpellVertSmaller.png", center=true, invert=false); } module eurorackMountHoles(php, holes, hw module eurorackMountHolesTopRow(php, hw, holes/2); } eurorackPanel(panelHp, holeCount,holeWidth); if (walls) { size = 200) at: https://www.myfonts.com/collections/quentin-font-urw?tab=individualStyles font_for_label = "Futura Md BT:style=Medium"; STLs, 10hp version, others schematics b404e3f9c5 Update luther's layout b22080a808 More experimentation with panel alignment before printing f6c7924538ef12da2abc179ebcc8f08e4164e698 main synth_tools/Schematics/SynthMages.pretty/eurorack_rail_hole.kicad_mod 24 lines Binary files /dev/null and b/3D Printing/AD&D 1e spell names in Filmoscope setup Add ground fills, fix some clearance issues, make all power traces large From 56529bef3a0c7d0b31cfccd6b6ce971fb35b4e9c Mon Sep 17 00:00:00 2001 Subject: [PATCH] Use THT electrolytics, finish SMT layout, try on quentin font for size f51b7b97734e404127fa5d5d263acbfd66f116e4 Add schematic, start on PCB with exploratory 8hp layout 2x Sockets, all three pins need wires: glide in (sleeve and normal both GND) 6x Sockets, 2pin: - all step switches (all go to same bus run/stop 2x Pushbutton switches, all 2pin: - all step switches (all go to same bus) - run/stop 2x Pushbutton switches, all 2pin: - step - reset Pots, 3-pin: Glide attenuator (B10k) (join two left pins from below Pots, 2-pin: - Glide, manual (A100k) (two left pins, from below) Pots, 2-pin: - Glide, manual (A100k) (two left pins, from below Pots.

New Pull Request

Labels Milestones