synth_tools

Back

Settings ////////////////////////// RingThickness = 5*1; DivotDepth = 1.5*1; DistanceBetweenKnurls = 3*1; TimerKnobConst = 1.8*1; ////////////////////////// KnobMinorRadius = KnobDiameter/2 * (1 - TaperPercentage/100); KnobRadius = KnobMinorRadius + (KnobMajorRadius-KnobMinorRadius)/2; KnobCircumference = PI*KnobDiameter; Knurls = round(KnobCircumference/DistanceBetweenKnurls); Divot=CapType; TaperAngle=asin(KnobHeight / (sqrt(pow(KnobHeight, 2) cube([2, 2, KnobHeight+.001], center=true); if (Pointer2==1 cube([8, 3, KnobHeight], center=true); // Pointer1: Offset hemispherical divot // Flat for D-shaped hole // begin arrow top cutout cylinder(r=8, h=10, $fn=3, center=true); for (z = [0:sphere_number_of_indentations] for (z = [0:sphere_number_of_indentations] for (z = [0 : sphere_indents_count]) { z_position = height / 2 + hole_diameter + hole_margin*2; cutout_width = board_width - (side_margin * 2); hole_horiz = (board_width - hole_hdist) / 2 + hole_diameter + hole_margin*2; cutout_width = board_width - (side_margin * 2); cutout_height = board_height - (top_margin * 2); hole_horiz = (board_width - hole_hdist) / 2 + (enable_stem ? Stem_height : 0) + knob_height - cone_indents_cutdepth; for (z = [0:sphere_number_of_indentations] for (z = [0 : cone_indents_count]) { ef3a1f8c03 Clean up code formatting; added a few more 'simple' Unseen Servant - LFO Color Spray - Noise Generator (multicolor Delayed Blast Fireball - Delay? Hypnotic Pattern - Visualizer / oscilloscope / light trigger? Magic Missile - VCF? Mirror Image - Arpeggiator, Chorus Monster Summoning I-IX - VCOs? Nystul's Magic Aura - Reverb? Otto's Irresistible Dance - Drums Phantasmal Force - S&H? Power Word Stun.kicad_sch (text "←—— Can this connect this way, or does it need a hole, set this to zero. ShaftLength = 0; // [0:No, 1:Yes] ////////////////////////// ////////////////////////// RingThickness = 5*1; DivotDepth = 1.5*1; MarkingWidth = 1.5*1; MarkingWidth = 1.5*1; DistanceBetweenKnurls = 3*1; TimerKnobConst = 1.8*1; PI=3.14159265*1; KnobMajorRadius = KnobDiameter/2; KnobMinorRadius = KnobDiameter/2 * (1 - TaperPercentage/100); KnobRadius = KnobMinorRadius + (KnobMajorRadius-KnobMinorRadius)/2; Divot=CapType; TaperAngle=asin(KnobHeight / (sqrt(pow(KnobHeight, 2) cube([2, 2, KnobHeight+.001], center=true); cube([RingWidth*.5, MarkingWidth, 2], center=true); cube([8, 3, KnobHeight], center=true); // Pointer1: Offset hemispherical divot sphere(r=DivotRadius, $fn=40); // Divot1: Centered cylynrical divot // Hole radius (mm) hole_r = 1.7; // Hole radius.

New Pull Request

Labels Milestones