Labels Milestones
Back(1/4in) stereo jack, horizontal PCB mount, black chrome shell, https://www.neutrik.com/en/product/nc5fbh-b B Series, 3 pole male XLR receptacle, grounding: separate ground contact to mating connector shell and front panel, lateral right PCB mount, https://www.neutrik.com/en/product/nc3faah2 AA Series, 3 pole male XLR receptacle, grounding: separate ground contact to mating connector shell to pin1 and front panel, horizontal PCB mount, asymmetric push, https://www.neutrik.com/en/product/ncj6fa-h-da Combo A series, 3 pole XLR female receptacle with 6.35mm (1/4in) stereo jack, horizontal PCB mount, https://www.neutrik.com/en/product/nc3fahr2 A Series, 3 pole female XLR receptacle, grounding: without ground / shell contact, vertical PCB mount, https://www.neutrik.com/en/product/nc3fahr1 A Series, 3 pole male XLR receptacle, grounding: separate ground contact to mating connector shell and front panel, vertical PCB mount, https://www.neutrik.com/en/product/nc5mah A Series, 3 pole male XLR receptacle, grounding: separate ground contact to mating connector shell and front panel, horizontal PCB mount, https://www.neutrik.com/en/product/nc3mav-0 A Series, 4 pole female XLR receptacle, grounding: separate ground contact to mating connector shell and front panel. This leaves a gap between the hub and circumference. * @todo Support knurling of the indenting cones. Cone_indents_count = 7; // generally-useful spacing amount for vertical columns of stuff center_adjust = 5; //knob_radius top_row = height - v_margin; working_increment = working_height / 5; row_1 = vertical_space/7; row_2 = row_1 + v_margin + 12; //knob_radius top_row = height - v_margin; working_increment = working_height / 6; // generally-useful spacing amount for vertical columns of stuff col_left = thickness * 2; right_rib_x = width_mm - h_margin; cv_in = [first_col, third_row, 0]; saw_out = [third_col, fourth_row, 0]; pwm_cv_lvl = [width_mm - h_margin - working_width/8, row_3, 0]; right_rib_x = width_mm - hole_dist_side, height - v_margin; working_increment = working_height / 6; // generally-useful spacing amount for vertical columns of stuff col_left = h_margin; bottom_row = v_margin + 12; //knob_radius top_row = height - v_margin - title_font; saw_out = [output_column, bottom_row, 0]; cv_in = [h_margin, row_1, 0]; fm_pot = [input_column + h_margin/2, row_1, 0]; fm_pot = [input_column + h_margin/2, row_1, 0]; triangle_out = [width_mm-h_margin-working_width/4, row_1, 0]; f_tune = [width_mm/2 + h_margin, top_row, 0]; left_rib_x = thickness * 1.2; right_rib_x = width_mm - h_margin; //special-case the knob (in mm). If dome cap is selected, it is safe to put the output jacks bottom_row = v_margin + 12; row_1 = bottom_row.
- Piher PT-15-H06, http://www.piher-nacesa.com/pdf/14-PT15v03.pdf Potentiometer vertical.
- 6.116634e-14 -1.000000e+00 7.228985e-14 facet normal.
- 0.39254 -0.665267 0.635084 facet normal -0.464833 -0.31635.