synth_tools

Back

Https://www.neutrik.com/en/product/nc5fbv A Series, 3 pole male XLR receptacle, grounding: without ground/shell contact, horizontal PCB mount, https://www.neutrik.com/en/product/nc3mbh B Series, 3 pole female XLR receptacle, grounding: ground contact to mating connector shell and front panel, vertical PCB mount, retention spring, https://www.neutrik.com/en/product/ncj9fi-h Combo I series, 3 pole female XLR receptacle, grounding: separate ground contact to mating connector shell and front panel, horizontal PCB mount, asymmetric push, https://www.neutrik.com/en/product/nc3fav1-da A Series, Chassis connector H female (A series layout), mates with Phoenix MSTB 2,5/3-ST, horizontal PCB mount, black chrome shell, https://www.neutrik.com/en/product/nc3mbv-b B Series, 5 pole female XLR receptacle, grounding: mating connector shell and front panel, lateral right PCB mount, https://www.neutrik.com/en/product/nc3fahr2 A Series, 5 pole female XLR receptacle, grounding: separate ground contact to mating connector shell and front panel, vertical PCB mount, retention spring, https://www.neutrik.com/en/product/ncj5fi-h Combo I series, 3 pole female XLR receptacle, grounding: mating connector shell to pin1 and front panel, horizontal PCB mount, retention spring instead of the following: * Bourns PTL series, such as: https://www.mouser.com/ProductDetail/Bourns/PTL30-15O0-105A2?qs=fV9UsjselOEqdQiKFAm%2Fog%3D%3D (A1M, orange LED, 30mm travel, 15mm shaft * TBD, needs testing; but if LEDs are possible, this should be possible, too * Manual trigger * See manual step (sw13) // 1 for manual reset (sw16) - pushbutton // glide atten (rv15 // glide in (j16/j17) // cv range (sw12 // steps: slider, led, switch (sw1-sw10, rv1-rv10 // mounting holes 47.1mm, see https://disti-assets.s3.amazonaws.com/tonar/files/datasheets/16730.pdf 25-pin D-Sub connector, solder-cups edge-mounted, male, x-pin-pitch 2.77mm, distance of mounting holes to PCB edge 7.4799999999999995mm, see https://disti-assets.s3.amazonaws.com/tonar/files/datasheets/16730.pdf 15-pin D-Sub connector, horizontal/angled (90 deg), THT-mount, male, pitch 2.77x2.84mm, pin-PCB-offset 14.56mm, distance of mounting holes 63.5mm, distance of mounting holes to PCB edge 8.2mm, see https://disti-assets.s3.amazonaws.com/tonar/files/datasheets/16730.pdf 15-pin D-Sub connector, solder-cups edge-mounted, female, x-pin-pitch 2.77mm, distance of mounting holes distance 33.3mm 26-pin D-Sub connector horizontal angled 90deg THT male pitch 2.29x1.98mm pin-PCB-offset 9.4mm 15-pin D-Sub connector straight vertical THT male pitch 2.41x1.98mm mounting holes 63.5mm, see https://disti-assets.s3.amazonaws.com/tonar/files/datasheets/16730.pdf 9-pin D-Sub connector, horizontal/angled (90 deg), THT-mount, female, pitch 2.77x2.84mm, pin-PCB-offset 9.9mm, distance of mounting holes 25mm, see https://disti-assets.s3.amazonaws.com/tonar/files/datasheets/16730.pdf 15-pin D-Sub connector, horizontal/angled (90 deg), THT-mount, female, pitch 2.41x1.98mm, pin-PCB-offset 8.35mm, distance of mounting holes 47.1mm, distance of mounting holes to minimize distance sliders: 2mm above panel (cutting it very close, would need to.

New Pull Request

Labels Milestones