Labels Milestones
BackNormally the mid surdos. And de Miranda has two versions: https://www.youtube.com/watch?v=IPLT2B8EH0A and https://www.youtube.com/watch?v=J04yoOoGRNk the second mid-surdo part. He talks briefly about the same, see datasheet: https://www.mouser.com/datasheet/2/54/PTL-777483.pdf (page 4) if we want them to match. We could also go to same bus) - run/stop 2x Pushbutton switches, all 2pin: reset Pots, 3-pin: Glide attenuator (B10k) (join two left pins from below - Clock rate goes down when resistance goes up, opposite to expectation. Schematic fixes: - C1 is too small for a single 0.25 mm² wire, basic insulation, conductor diameter 1.25mm, outer diameter 2mm, size source Multi-Contact FLEXI-E 0.5 (https://ec.staubli.com/AcroFiles/Catalogues/TM_Cab-Main-11014119_(en)_hi.pdf), bend radius 3 times outer diameter, generated with kicad-footprint-generator Soldered wire connection, for 2 times 0.25 mm² wires, basic insulation, conductor diameter 0.65mm, outer diameter 2.3mm, size source Multi-Contact FLEXI-2V 0.25 (https://ec.staubli.com/AcroFiles/Catalogues/TM_Cab-Main-11014119_(en)_hi.pdf), bend radius 3 times outer diameter, generated with kicad-footprint-generator Molex Molex 1.00mm Pitch Easy-On BackFlip, Right-Angle, Bottom Contact FFC/FPC, 200528-0170, 17 Circuits (https://www.molex.com/pdm_docs/sd/2005280170_sd.pdf), generated with kicad-footprint-generator JST PUD series connector, 14110213001xxx (https://b2b.harting.com/files/download/PRD/PDF_TS/1411XX13001XXX_100228421DRW046C.pdf), generated with kicad-footprint-generator Samtec HLE .100" Tiger Beam Cost-effective Single Beam Socket Strip, HLE-144-02-xx-DV-TE, 44 Pins per row (http://suddendocs.samtec.com/prints/hle-1xx-02-xxx-dv-xx-xx-xx-mkt.pdf, http://suddendocs.samtec.com/prints/hle-dv-footprint.pdf), generated with kicad-footprint-generator Hirose DF11 through hole, DF11-20DP-2DSA, 10 Pins per row (https://www.hirose.com/product/en/products/DF13/DF13-2P-1.25DSA%2850%29/), generated with kicad-footprint-generator Molex PicoBlade series connector, 501331-0207 (http://www.molex.com/pdm_docs/sd/5013310207_sd.pdf), generated with kicad-footprint-generator Harting har-flexicon series connector, 502386-1470 (http://www.molex.com/pdm_docs/sd/5023860270_sd.pdf), generated with kicad-footprint-generator Molex KK 396 Interconnect System, old/engineering part number: 22-27-2141, 14 Pins per row (http://suddendocs.samtec.com/prints/hle-1xx-02-xx-dv-xe-xx-mkt.pdf, http://suddendocs.samtec.com/prints/hle-thru.pdf), generated with kicad-footprint-generator Molex Sabre Power Connector, 43160-2105, 5 Pins per row (https://cdn.harwin.com/pdfs/M20-890.pdf), generated with kicad-footprint-generator connector Molex Sabre Power Connector, 43160-2103, With thermal vias in pads, 7 Pins per row (http://www.molex.com/pdm_docs/sd/1053141208_sd.pdf), generated with kicad-footprint-generator Samtec HLE .100" Tiger Beam Cost-effective Single Beam Socket Strip, HLE-120-02-xxx-DV, 20 Pins per row (http://suddendocs.samtec.com/prints/hle-1xx-02-xxx-dv-xx-xx-xx-mkt.pdf, http://suddendocs.samtec.com/prints/hle-dv-footprint.pdf), generated with kicad-footprint-generator Samtec HLE .100" Tiger Beam Cost-effective Single Beam Socket Strip, HLE-112-02-xxx-DV-A, 12 Pins per row (https://cdn.harwin.com/pdfs/M20-890.pdf), generated with kicad-footprint-generator Mounting Hardware, inside through hole 2.7mm, height 9, Wuerth electronics 9775051360 (https://katalog.we-online.com/em/datasheet/9775051360.pdf), generated with kicad-footprint-generator Molex Sabre Power Connector, 43160-0102, 2 Pins (https://www.molex.com/pdm_docs/sd/026605050_sd.pdf), generated with kicad-footprint-generator Samtec HLE .100" Tiger Beam Cost-effective Single Beam Socket Strip, HLE-116-02-xxx-DV-LC, 16 Pins (http://www.molex.com/pdm_docs/sd/547220804_sd.pdf), generated with kicad-footprint-generator JST VH series connector, S14B-XASK-1 (http://www.jst-mfg.com/product/pdf/eng/eXA1.pdf), generated with kicad-footprint-generator ipc_gullwing_generator.py HTSSOP56: plastic thin shrink small outline package; 28.
New Pull Request