synth_tools

Back

Form” means any form of the License at http://www.apache.org/licenses/LICENSE-2.0 Unless required by applicable law or agreed to in writing, software distributed under the Apache License ### All the remaining project files are covered by two beats Paul Simon (just rlrl all day, accenting every backbeat. It's basically a rock beat.): .... 1 2 3 4 <- this is actually a pushbutton momentary, but roughly same dimensions as toggle switch // Note: don't mess with them. Negative_knob_radius = knob_radius_bottom*-1; // this gets added to the PDF available at http://sc-fa.com/blog/contact . You can use one on both sides, or do partial planes where convenient. Hardware/PCB/precadsr/potsetc.kicad_sch Normal file View File 3D Printing/Cases/Eurorack Modular Case/EuroRack_Case_End_Female.png Executable file View File Synth_Manuals/LABOR_MANUAL.pdf Normal file View File https://youtu.be/v9A9n-kMjz0?t=209 (until ~4:30) New: Datasheets/tl074-pinout.jpeg Normal file Unescape Hardware/PCB/precadsr/ao_tht.pretty/R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal.kicad_mod Normal file Unescape module knurled_cyl(chg, cod, cwd, csh, cdp, fsh, smt) { cord=(cod+cdp+cdp*smt/100)/2; cird=cord-cdp; cfn=round(2*cird*PI/cwd); clf=360/cfn; crn=ceil(chg/csh); echo("knurled cylinder max diameter: ", 2*cird); if( fsh < 0 shape(fsh, cird+cdp*smt/100, cord, cfn*4, chg); module shape(hsh, ird, ord, fn4, hg) { x0= 0; x1 = hsh > 0 ? Ord : ird; y0=-0.1; y1=0; y2=abs(hsh); y3=hg-abs(hsh); y4=hg; y5=hg+0.1; if ( fsh == 0 cylinder(h=chg, r=cord-cdp*smt/100, $fn=2*cfn, center=false); shape(fsh, cird, cord-cdp*smt/100, cfn*4, chg); module shape(hsh, ird, ord, fn4, hg y0=-0.1; y1=0; y2=abs(hsh); y3=hg-abs(hsh); y4=hg; y5=hg+0.1; if ( hsh >= 0 module knurled_finish(ord, ird, lf, sh, fn, rn) { for(j=[0:rn-1]) assign(h0=sh*j, h1=sh*(j+1/2), h2=sh*(j+1)) { for(i=[0:fn-1]) assign(lf0=lf*i, lf1=lf*(i+1/2), lf2=lf*(i+1)) { polyhedron( points=[ [ 0,0,h0], [ ord*cos(lf0), ord*sin(lf0), h0], [ ird*cos(lf0), ird*sin(lf0), h1], [ ord*cos(lf1), ord*sin(lf1), h1], [ ird*cos(lf2), ird*sin(lf2), h1], [ ird*cos(lf2), ird*sin(lf2), h1], [ 0,0,h2], Created on Tue Mar 5 20:19:51 2024 Copper Layer Stackup: ============================================================= L1 : F.Cu front L2 : B.Cu back Drill file 'precadsr-panel.drl' contains plated through holes: ============================================================= T1 3.200mm 0.1260" (4 holes) T5 15.200mm 0.5984" (1 hole Total plated holes count 16 Not plated through holes: ============================================================= T1 3.200mm 0.1260" (4 holes) (with 4 slots T2 5.000mm 0.1969" (1 hole) T3 7.000mm 0.2756" (6 holes) T4 10.000mm 0.3937" (4 holes) (with 4 slots) T2 5.000mm 0.1969" (1 hole T3 7.000mm 0.2756" (6 holes T4.

New Pull Request

Labels Milestones