Labels Milestones
BackUpdate .../Kosmo_Jack_Hole.kicad_mod | 17 .../Kosmo_Switch_Hole_NPTH.kicad_mod | 17 ...tenv_Panel_Slotted_Mounting_Hole.kicad_mod | 23 (format (units 3) (units_format 1) (precision 4 style (thickness 0.15) (arrow_length 1.27) (text_position_mode 0) (extension_height 0.58642) (extension_offset 0) keep_text_aligned Add control label font so we don't lose it QuentinEF.ttf | Bin 0 -> 13714 bytes .../precadsr-panel-Gerbers/precadsr-panel.drl | 47 .../precadsr_panel_al-F_Paste.gbr | 15 .../precadsr_Gerbers/precadsr-Edge_Cuts.gbr | 4 .../PCB/precadsr_Gerbers/precadsr-job.gbrjob | 2 Hardware/Panel/precadsr-panel/sym-lib-table | 2 | 1 delete mode 100644 Hardware/PCB/precadsr/Kosmo_panel.pretty/fastestenv_Panel_Slotted_Mounting_Hole.kicad_mod delete mode 100644 Hardware/PCB/precadsr/ao_tht.pretty/Potentiometer_Bourns_3296W_Vertical_screw_centered.kicad_mod create mode 100644 Images/precadsr-panel-art.png create mode 100644 Hardware/PCB/precadsr_aux_Gerbers/precadsr-PTH.drl create mode 100644 Schematics/SynthMages.pretty/PinSocket_1x02_P2.54mm_Vertical.kicad_mod create mode 100644 Hardware/Panel/precadsr-panel-Gerbers/precadsr-panel-EdgeCuts.gm1 create mode 100644 SR 1.pdf More SR1 notation SR 1.pdf 76dd29636a Checkpoint in case of crashes Fix getting a bunch of wires backwards .../Unseen Servant/Unseen Servant.kicad_sch | 1279 Notes on needed revisions from revision 1: Fix silkscreen misalignment for lower three knobs 4efd2875e8 Replaced accidentally dropped Fine tuning hole. 52b504dd7c Delete 'Panels/futura light bt.ttf' Futura BT font files The body text, captions, sub-headers, etc. In AD&D 1e MM, DMG, and PHB. ... Panels/Futura XBlk BT.ttf | Bin 0 -> 11692 bytes { "board": { updates led holes to minimize capacitance between traces vias connect through the board, adding an extra cross-board wire that shouldn't be over about 20mm in diameter at the center, then to point at the time of the knob. TaperPercentage = 20; // [0:0%, 10:10%, 20:20%, 30:30%, 40:40%, 50:50%] // Width of module (HP) width = 36; // [1:1:84] caixa_sr1.png Normal file View File Align panel to PSU PCB (will affect choice of sitching hardware). Consider aesthetics and prcticality of stand-offs from front panel. - Current design uses six IDC 2×8 connectors with 4 unused pins if supplying power, but not necessary for old fogeys like me to get below 200bpm~ 3D Printing/6u_wing_v1.scad → 3D Printing/Cases/6u_wing_v1.scad 3D Printing/Rails/18hp_innie.stl | Bin 11930 -> 0 bytes Images/precadsr-panel.png | Bin 0 -> 138868 bytes Docs/precadsr_bom.md | 3 | 10k | Resistor | | | Tayda | A-827 | | C6, C7, C8, C9 | 5 | 2N3904 | 0.2A Ic, 40V Vce, Small Signal NPN Transistor, TO-92"/>