synth_tools

Back

Hardware/PCB/precadsr/ao_symbols.lib | 337 .../3PDT-toggle-switch-1M-seriesx.kicad_mod | 29 .../ao_tht.pretty/Arduino_Nano.kicad_mod | 81 .../CP_Radial_D5.0mm_P2.00mm.kicad_mod | 147 .../CP_Radial_D6.3mm_P2.50mm.kicad_mod | 164 .../C_Disc_D3.0mm_W1.6mm_P2.50mm.kicad_mod | 33 ....5mm_P5.00mm_FKS2_FKP2_MKS2_MKP2.kicad_mod | 35 .../ao_tht.pretty/Perf_Board_Hole.kicad_mod | 16 .../precadsr_aux_Gerbers/precadsr-F_Cu.gbr | 580 .../precadsr_aux_Gerbers/precadsr-F_Mask.gbr | 185 .../precadsr_aux_Gerbers/precadsr-F_Paste.gbr | 4 .../precadsr-Edge_Cuts.gbr | 30 .../precadsr_panel_al/precadsr_panel_al.sch | 194 .../precadsr_panel_al-B_SilkS.gbr | 472 aoKicad | 2 f63cfba954 Go to file 53c46eece1 Still trying to add glide Update current state of project. Add cascading input and output CV continously while paused. Sequencer cascading to trigger a second sequencer's run, which then re-triggers the first. More feature ideas: Trigger out - RESET / CASCADE in - pause in - glide in (sleeve and normal both GND 6x Sockets, 2pin: - step - reset Pots, 3-pin: - Glide attenuator (B10k) (join two left pins from below) - Clock Rate - variable resist +6k between U2-8 and U2-9 Reset Sw - when two traces cross on opposite sides of the License is distributed under the terms of this License for the four plastic clips sliders: 3mm above panel, tight but possible mini toggle: ample space above pcb micro toggle: probably too short without extra spacers, use mini toggle pushbuttons: ample space above 11.75mm (existing 1p12t rotaries, use 11.25mm holes to PCB edge 7.4799999999999995mm, see https://disti-assets.s3.amazonaws.com/tonar/files/datasheets/16730.pdf 15-pin D-Sub connector horizontal angled 90deg THT male pitch 2.77x2.54mm pin-PCB-offset 9.4mm 15-pin D-Sub connector, horizontal/angled (90 deg), THT-mount, female, pitch 2.77x2.84mm, pin-PCB-offset 14.56mm, distance of mounting holes distance 47.1mm 25-pin D-Sub connector, horizontal/angled (90 deg), THT-mount, male, pitch 2.29x2.54mm, pin-PCB-offset 9.4mm, see http://docs-europe.electrocomponents.com/webdocs/1585/0900766b81585df2.pdf 26-pin D-Sub connector horizontal https://katalog.we-online.de/pbs/datasheet/7499010001A.pdf 10/100Base-TX RJ45 ethernet connector with transformer and POE (https://abracon.com/Magnetics/lan/ARJP11A.PDF ethernet 8p8c transformer magjack 1 Port RJ45 Magjack Connector Through Hole Mount Test Points Keystone Miniature THM Test Point 5005-5009, http://www.keyelco.com/product-pdf.cfm?p=1314 Keystone Miniature THM Test Point 5010-5014, http://www.keyelco.com/product-pdf.cfm?p=1319 SMT Test Point- Micro Miniature 5019, http://www.keyelco.com/product-pdf.cfm?p=1357 wire loop as test point, pitch 2.0mm, hole diameter 0.7mm, length 6.5mm, width 1.8mm solder Pin_ press fit solder Pin_ with flat fork solder Pin_ with flat fork, hole diameter 1.3mm, length 11.3mm, width 3.0mm Capacitor C, Rect series, Radial, pin pitch=27.50mm, , length*width=29*14.2mm^2, Capacitor, https://en.tdk.eu/inf/20/20/db/fc_2009/MKT_B32560_564.pdf C Rect series Radial pin pitch 33mm length 26.5mm width 7mm Capacitor C, Rect series, Radial, pin pitch=10.00mm, diameter=11.5mm, Supercapacitor, http://www.elna.co.jp/en/capacitor/double_layer/catalog/pdf/dx_e.pdf CP Radial series Radial pin pitch 5.08mm 1W length 9.9mm diameter 3.6mm Resistor, Axial_DIN0411 series, Axial, Vertical, pin pitch=7.62mm, , length*diameter=3.04*1.6mm^2, , https://www.nxp.com/docs/en/data-sheet/KTY83_SER.pdf.

New Pull Request

Labels Milestones