synth_tools

Back

Traces }, More tweaks after pro review PSU/Synth Mages Power Word Stun.kicad_pro 555 lines width = 24; // [1:1:84] /* [Holes] */ hole_dist_top = 2.5; rail_clearance = 8.5; // mm from very top/bottom edge and where it is not possible or desirable to put reinforcing walls; i.e. The thickness of 2mm // for inset labels, translating to this height controls label depth label_inset_height = thickness-1; // Width of module (HP) width = 36; // [1:1:84] width = 10; label_font = 6; //knob_radius saw_out = [third_col, fourth_row, 0]; //Fifth row interface placement triangle_out = [output_column, bottom_row, 0]; fm_in = [h_margin+working_width/8, row_3, 0]; manual_2 = [left_col, row_7, 0]; manual_1 = [left_col, row_7, 0]; cv_in_1b = [right_col, row_5, 0]; cv_in_2a = [left_col, row_6, 0]; cv_1b_atten = [right_col, row_5, 0]; cv_in_2a = [left_col, row_2, 0]; fm_in = [first_col, first_row, 0]; //Second row interface placement f_tune = [second_col, fourth_row, 0]; pwm_cv_lvl = [width_mm - h_margin - working_width/8, row_4, 0]; pwm_cv_lvl = [width_mm - h_margin - working_width/8, row_2, 0]; fm_in = [input_column - h_margin/2, bottom_row, 0]; pwm_pot = [input_column - h_margin/2, row_1, 0]; right_rib_x = width_mm - 10 - center_adjust; center_col = width_mm/2; //mm third_col = 60.7-center_adjust; //mm cv_in = [input_column, row_2, 0]; triangle_out = [output_column, bottom_row, 0]; c_tune = [second_col, third_row, 0]; saw_out = [h_margin + working_width/4, row_1, 0]; fm_pot = [input_column + h_margin/2, row_1, 0]; pwm_in = [width_mm - h_margin - working_width/8, row_4, 0]; left_rib_x = hole_dist_side + thickness; v_margin = hole_dist_top*2 + thickness; v_margin = hole_dist_top*2 + thickness; v_margin = hole_dist_top*2; v_margin = hole_dist_top*2; left_rib_x = hole_dist_side + thickness; right_rib_x = width_mm - thickness*2; // draw panel, subtract holes union() { cube([board_width, board_height, thickness]); cylinder(thickness+standoff_height, r=standoff_radius, $fn=360); cylinder(h=thickness+standoff_height, r=standoff_radius, $fn=360); cylinder(h=thickness+standoff_height, r=standoff_radius, $fn=360); cylinder(h=thickness+standoff_height, r=standoff_radius, $fn=360); cylinder(h=thickness+standoff_height, r=standoff_radius, $fn=360); cylinder(h=thickness+standoff_height, r=standoff_radius, $fn=360); cylinder(h=thickness+standoff_height, r=standoff_radius, $fn=360); cylinder(h=thickness+standoff_height, r=standoff_radius, $fn=360); cylinder(h=thickness+standoff_height, r=standoff_radius, $fn=360); cylinder(h=thickness+standoff_height, r=standoff_radius, $fn=360); cube([cutout_width, cutout_height, thickness+3]); cylinder(h=thickness+standoff_height+3, r=hole_radius, $fn=360); vertex 0 7.49999 6.0001 vertex -4.16677 6.23601 6.0001 vertex -4.16677 6.23601 6.0001 vertex -7.35588 -1.46317 6.0001 vertex 4.16677 6.23601 6.0001 vertex -4.16677 6.23601 6.0001 vertex 2.87013 6.92908 6.0001 vertex 1.46317 -7.35588 6.0001 vertex 0 7.5203 6.0001 facet normal 0.112453 0.551187 -0.826769 vertex 1.08464 2.68773 18.9318 facet normal 0.0819177 -0.0822333 -0.993241 facet normal 0.828666 -0.0815498 0.55377 facet normal -0.0647447 -0.0692189 0.995498 facet normal -0.47938 -0.871977 0.0992491 vertex -3.40623 7.23862 20 facet normal 9.162093e-001 -4.006999e-001 0.000000e+000 vertex -5.709703e+000 -4.193455e+000 9.983999e+000.

New Pull Request

Labels Milestones