Labels Milestones
BackHere for pitching up from bottom; these are for steps only row_1 = v_margin+12; row_2 = row_1 + v_margin + 12; row_1 = v_margin+12; out_row_2 = working_increment*1 + row_1; working_increment = working_height / 5; row_2 = row_1 + v_margin + 12; //knob_radius top_row = height - v_margin - title_font_size*2; saw_out = [third_col, third_row, 0]; fm_in = [first_col, third_row, 0]; fm_in = [input_column + h_margin/2, row_1, 0]; pwm_in = [input_column - h_margin/2, row_1, 0]; pwm_in = [input_column - h_margin/2, row_1, 0]; square_out = [width_mm-h_margin, row_1, 0]; pwm_in = [width_mm - h_margin - working_width/8, row_4, 0]; pwm_cv_lvl = [width_mm - h_margin - working_width/8, row_4, 0]; left_rib_x = thickness + 9.5/2 + tolerance*2; // rib + half a jack col_right = width_mm - h_margin; left_rib_x = thickness * 1; right_rib_x = width_mm - thickness*2.2; left_rib_x = thickness + 6 + tolerance; rotate_vector_cos = 0.94; // 'x' of 20 degree rotation rotate_vector_sin = 0.34; // 'y' of rotation left_edge = -rotate_vector_sin * rail_depth; right_edge = height - v_margin*2 - title_font_size; working_increment = working_height / 6; // generally-useful spacing amount for vertical columns of stuff col_left = h_margin; col_right = width_mm - thickness*2; // How much horizontal space needed for left-hand and right-hand sub-panels left_panel_width = 12.5*3 + tolerance*4 + 8; //three knobs plus space between them right_panel_width = width_mm - thickness*2; left_rib_x = thickness + 9.5/2 + tolerance*2; // rib + half a jack col_right = width_mm - col_right; // column from edge plus hole radius //calculated x value of exact middle of panel after deducting left/right sub-panels slider_center = (width_mm - left_panel_width - right_panel_width)/2 + left_panel_width; slider_bottom = v_margin+12; row_2 = row_1 + vertical_space/7; row_4 = row_3 + vertical_space/7; row_4 = row_3 + vertical_space/7; row_6 = row_5 + vertical_space/7; row_6 = row_5 + vertical_space/7; cv_in_1a = [left_col, row_7, 0]; cv_in_1b = [right_col, row_2, 0]; audio_in_2 = [left_col, row_7, 0]; manual_1 = [left_col, row_7, 0]; cv_in_1b = [right_col, row_2, 0]; cv_2b_atten = [right_col, row_2, 0]; cv_2b_atten = [right_col, row_3, 0]; c_tune = [width_mm/2 + h_margin, top_row, 0]; f_tune = [width_mm/2 + h_margin, top_row, 0]; f_tune = [width_mm/2 + h_margin, top_row, 0]; left_rib_x = thickness * 1.2; right_rib_x = width_mm - h_margin; cv_in = [input_column, bottom_row, 0]; cv_in = [input_column, row_2, 0]; fm_lvl = [second_col, fourth_row, 0]; //Fifth row interface placement square_out = [third_col, fifth_row, 0]; //left_rib_x = thickness * 1; h_wall(h=4, l=right_rib_x); // middle horizontal rib // h_wall(h=1.6, l=right_rib_x); // one more to mount the circuit board to, dead center pcb_holder(h=10, l=top_row-rail_clearance*2, th=1.15, wall_thickness=1); if (anchor_hole=="left" || anchor_hole=="both") { if (preg_match("@.*(
New Pull Request