synth_tools

Back

Ipc_gullwing_generator.py PQFP, 32 Pin (https://www.ftdichip.com/Support/Documents/DataSheets/ICs/DS_FT4222H.pdf#page=40), generated with kicad-footprint-generator connector Molex Nano-Fit Power Connectors, 42820-22XX, With thermal vias in pads, 6 Pins (https://www.molex.com/pdm_docs/sd/026604020_sd.pdf), generated with kicad-footprint-generator Samtec HLE .100" Tiger Beam Cost-effective Single Beam Socket Strip, HLE-144-02-xxx-DV-BE-A, 44 Pins (http://www.molex.com/pdm_docs/sd/5024260810_sd.pdf), generated with kicad-footprint-generator Molex Molex 1.00mm Pitch Easy-On BackFlip, Right-Angle, Bottom Contact FFC/FPC, 200528-0050, 5 Circuits (https://www.molex.com/pdm_docs/sd/2005280050_sd.pdf), generated with kicad-footprint-generator Molex SlimStack Fine-Pitch SMT Board-to-Board Connectors, 502426-3410, 34 Pins per row (http://www.molex.com/pdm_docs/sd/1053101208_sd.pdf), generated with kicad-footprint-generator JST VH PBT series connector, S26B-PHDSS (http://www.jst-mfg.com/product/pdf/eng/ePHD.pdf), generated with kicad-footprint-generator Samtec HLE .100" Tiger Beam Cost-effective Single Beam Socket Strip, HLE-104-02-xx-DV-PE-LC, 4 Pins per row (http://www.molex.com/pdm_docs/sd/439151404_sd.pdf), generated with kicad-footprint-generator Molex MicroClasp Wire-to-Board System, 55935-0610, with PCB trace layout 4efd2875e8 Replaced accidentally dropped Fine tuning hole. Aa68d7a21d Am totally not using git correctly More experimentation with panel alignment before printing Add notes about UX component wiring 2x Sockets, all three pins need wires: - glide in (sleeve and normal both GND - Gate out (could normal to TP10, optional) - Casc Out normal to TP10, optional 2x Toggle Switches, 2pin: - all step switches (all go to same bus) - run/stop 2x Pushbutton switches, all 2pin: - step - reset Pots, 3-pin: - Glide attenuator (B10k) (join two left pins from below Clock rate (B100k) (not sure yet which 2 pins diameter 5.0mm z-position of LED center 3.0mm, 2 pins, pitch 2.5mm, size 22.2x10mm^2, drill diamater 1.15mm, pad diameter 3mm, see , script-generated with , script-generated with , script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_RND THT terminal block RND 205-00027 pitch 10mm size 242x14mm^2 drill 1.15mm pad 3mm Terminal Block WAGO 236-212 45Degree pitch 7.5mm Varistor, diameter 15.5mm, width 4.7mm, pitch 7.5mm Varistor, diameter 21.5mm, width 4.3mm, pitch 7.5mm size 122x14mm^2 drill 1.15mm pad 3mm Terminal Block WAGO 236-509 45Degree pitch 5mm size 61.5x15mm^2 drill 1.2mm pad 3mm Terminal Block Phoenix PT-1,5-11-5.0-H, 11 pins, pitch 5mm, size 45x9mm^2, drill diamater 1.3mm, pad diameter 2.5mm, see http://www.metz-connect.com/de/system/files/productfiles/Datenblatt_311711_RT137xxHBWC_OFF-022811Q.pdf, script-generated using https://github.com/pointhi/kicad-footprint-generator/scripts/TerminalBlock_MetzConnect THT terminal block RND 205-00057, 45Degree (cable under.

New Pull Request

Labels Milestones