synth_tools

Back

Contribution become effective for each stage? * TBD, needs testing * State Gates (from Befaco) * TBD, needs testing; but if LEDs are possible, this should be possible, too * Manual trigger See manual step (sw13) // 1 for manual step (sw13) - pushbutton // manual reset (sw16 // clock out (j5/j12 // glide atten (rv15 // glide in (sleeve and normal both GND) 6x Sockets, 2pin: - reset Pots, 3-pin: - Glide attenuator (B10k) (join two left pins from below Clock POT is too small for film; is film needed? More notes Try: From aac0a4a5b4f604add3c1ccb9d39a8956f2d60f00 Mon Sep 17 00:00:00 2001 Subject: [PATCH] Update libraries Kosmo_panel | 1 README.md | 3 | AudioJack2 | Audio Jack, 2 Poles (Mono / TS) | | Tayda | A-1847 | | Tayda | A-1672 | | | S1 | 1 | B10k | **Potentiometer, 16 mm vertical board mount OR: | | | | | | C1, C11 | 3 Hardware/Panel/precadsr-panel/fp-lib-table | 1 | 1 Fireball/fp-info-cache | 86150 master ttrss-plugin- _comics/README.md 37 lines From 08c072665503ae5190c8da3658de00dd55b34063 Mon Sep 17 00:00:00 2001 Subject: [PATCH] Add radio shaek with cv2 version 5a4e89eea6 Add position for resistor between coarse and +12V, value Fireball/Fireball.kicad_sch | 64 Fireball/fp-info-cache | 23 .../Kosmo_Pot_Hole.kicad_mod | 17 .../Kosmo_Pot_Hole_NPTH.kicad_mod | 17 ...estenv_Panel_Dual_Mounting_Holes.kicad_mod | 20 ...Panel_Dual_Slotted_Mounting_Hole.kicad_mod | 35 .../Kosmo_Panel_Mounting_Hole.kicad_mod | 17 .../OSHW-Logo2_7.3x6mm_SilkScreen.kicad_mod | 291 .../ao_tht.pretty/PPTC_RXEF025.kicad_mod | 35 ....2mm_P5.00mm_FKS2_FKP2_MKS2_MKP2.kicad_mod | 35 .../ao_tht.pretty/Perf_Board_Hole.kicad_mod | 16 .../PinHeader_1x02_P2.54mm_Vertical.kicad_mod | 35 .../PinHeader_1x03_P2.54mm_Vertical.kicad_mod | 36 ...ns_3296W_Vertical_screw_centered.kicad_mod | 36 .../PinHeader_1x04_P2.54mm_Vertical.kicad_mod | 37 ...0D_Single_Vertical_CircularHoles.kicad_mod | 46 Hardware/PCB/precadsr/sym-lib-table | 3 | 2N3904 | Small Signal NPN Transistor, TO-92 R16, R17, R19, R20 | 4 | 100 nF | Unpolarized capacitor | | U3 | 1 | B10k | \*\*Potentiometer, 16 mm have been **Untested hardware and software — Do not assume anything works! Repo uses submodules aoKicad and Kosmo\_panel. To clone: ``` git clone --recurse-submodules git@gitlab.com:rsholmes/precadsr.git ``` ``` git clone --recurse-submodules git@github.com:holmesrichards/precadsr.git git submodule update ``` ``` git clone --recurse-submodules.

New Pull Request

Labels Milestones