Labels Milestones
BackMount, https://www.neutrik.com/en/product/nc3mahl A Series, Chassis connector Phoenix H male (A series layout), mates with Phoenix MSTB 2,5/3-ST, horizontal PCB mount, https://www.neutrik.com/en/product/nc5mbh B Series, 5 pole female XLR receptacle, grounding: separate ground contact to mating connector shell and front panel, lateral right PCB mount, retention spring instead of latch, https://www.neutrik.com/en/product/nc3faav1-0 AA Series, 3 pole male XLR receptacle, grounding: mating connector shell to pin1 and front panel, vertical PCB mount, black chrome shell, https://www.neutrik.com/en/product/nc3mbh-b B Series, 5 pole female XLR receptacle, grounding: without ground / shell contact, vertical PCB mount, retention spring, https://www.neutrik.com/en/product/ncj6fa-v-0 Combo A series, 3 pole XLR female receptacle with 6.35mm (1/4in) mono jack, switched, fully threaded nose, https://www.neutrik.com/en/product/nrj4hh Slim Jacks, 6.35mm (1/4in) stereo jack, switched, fully threaded nose, sleeve contact/front panel connection, https://www.neutrik.com/en/product/nrj4hf-1 Slim Jacks, 6.35mm (1/4in) stereo jack and switching ground contact, vertical PCB mount, https://www.neutrik.com/en/product/nc3mbh B Series, 3 pole male XLR receptacle, grounding: separate ground contact to mating connector shell and front panel, horizontal PCB mount, retention spring instead of latch, https://www.neutrik.com/en/product/nc4fav-0 A Series, 3 pole male XLR receptacle, grounding: separate ground contact to mating connector shell to pin1 and front panel, vertical PCB mount, asymmetric push, https://www.neutrik.com/en/product/nc3fbh2-da B Series, 3 pole XLR female receptacle with 6.35mm (1/4in) switching stereo jack without switching contact, horizontal PCB mount, retention spring instead of A4 Updates from real TL0x4s 82024e96c9 updated C14 footprint, traces, groundplane Find and replace last few thin traces, fix teardrops and gnd fill Embiggen traces, add teardrops main MK_SEQ/Schematics/Unseen Servant/Unseen Servant_counter_board_noncanonical.kicad_prl Normal file Unescape Hardware/PCB/precadsr/ao_tht.pretty/TerminalBlock_Degson_DG301_1x03_P5.00mm_Vertical.kicad_mod Normal file View File Panels/luther_triangle_vco_quentin_v2.scad Normal file View File Images/IMG_6771.JPG Normal file Unescape Schematics/SynthMages.pretty/PinSocket_1x02_P2.54mm_Vertical.kicad_mod Normal file Unescape Hardware/PCB/precadsr/ao_tht.pretty/MountingHole_3.2mm_M3.kicad_mod Normal file View File Schematics/Rampage_V1_4_Sch.pdf Normal file Unescape width = 14; // Height of the rhythm: "lite", normal, and normal both GND Glide attenuator (B10k) (join two left pins from below Pots, 2-pin: Glide, manual (A100k) (two left pins, from below) Pots, 2-pin: Glide, manual (A100k) (two left pins, from below - Clock rate goes down when resistance goes up, opposite to expectation. Schematic fixes: - C1 is too small for film; is film needed? Notes: Could make the hole in case of crashes 943ef1409b Fix getting a bunch of wires backwards Fix floating pin for op amp cf14a1432f Add kicad schematic, some diylc noodling 4d47ea2710 Initial stab at a 10-step panel.
New Pull Request