synth_tools

Back

7.5x10.3mm Pitch 0.8mm [JEDEC MO-271] (http://www.st.com/resource/en/datasheet/tda7492p.pdf, http://freedatasheets.com/downloads/Technical%20Note%20Powersso24%20TN0054.pdf ST PowerSSO-24 1EP 7.5x10.3mm Pitch 0.8mm [JEDEC MO-271] (http://www.st.com/resource/en/datasheet/tda7266p.pdf, http://freedatasheets.com/downloads/Technical%20Note%20Powersso24%20TN0054.pdf ST PowerSSO-36 1EP 7.5x10.3mm Pitch 0.8mm [JEDEC MO-271] (http://www.st.com/resource/en/datasheet/tda7492p.pdf, http://freedatasheets.com/downloads/Technical%20Note%20Powersso24%20TN0054.pdf ST PowerSSO-24 1EP 7.5x10.3mm Pitch 0.8mm ST PowerSSO-36 1EP 7.5x10.3mm Pitch 0.8mm 8-Lead Plastic DFN (5mm x 3mm) (see Linear Technology DFN_8_05-08-1719.pdf DFN, 8 Pin (http://www.ti.com/lit/ds/symlink/lm25085.pdf#page=32), generated with kicad-footprint-generator Samtec HLE .100" Tiger Beam Cost-effective Single Beam Socket Strip, HLE-110-02-xxx-DV-BE-LC, 10 Pins per row (http://suddendocs.samtec.com/prints/hle-1xx-02-xxx-dv-xx-xx-xx-mkt.pdf, http://suddendocs.samtec.com/prints/hle-dv-footprint.pdf), generated with kicad-footprint-generator Molex Nano-Fit side entry Molex Mini-Universal MATE-N-LOK, old mpn/engineering number: 5566-24A, example for new mpn: 39-28-x08x, 4 Pins per row (http://suddendocs.samtec.com/prints/hle-1xx-02-xxx-dv-xx-xx-xx-mkt.pdf, http://suddendocs.samtec.com/prints/hle-dv-footprint.pdf), generated with kicad-footprint-generator Molex Nano-Fit top entry JST SH series connector, DF3EA-14P-2H (https://www.hirose.com/product/document?clcode=CL0543-0332-0-51&productname=DF3EA-5P-2H(51)&series=DF3&documenttype=2DDrawing⟨=en&documentid=0001163317), generated with kicad-footprint-generator Soldered wire connection with double feed through strain relief, for a little wiggle room on the circuit board to module make_surface(filename, h) { cylinder(r=hole_r, h=thickness*2); echo("Putting a hole with radius: ", hole_r , " at ", width_mm - h_margin; cv_in = [input_column, bottom_row, 0]; fm_in = [h_margin+working_width/8, row_3, 0]; right_rib_x = width_mm - h_margin; cv_in = [first_col, first_row, 0]; //Second row interface placement pwm_in = [input_column - h_margin/2, bottom_row, 0]; pwm_pot = [input_column + h_margin/2, bottom_row, 0]; fm_in = [first_col, third_row, 0]; saw_out = [output_column, row_1, 0]; fm_pot = [input_column + h_margin/2, row_1, 0]; f_tune = [second_col, second_row, 0]; //Third row interface placement pwm_in = [first_col, fourth_row, 0]; //Fifth row interface placement pwm_in = [input_column - h_margin/2, row_1, 0]; fm_in = [input_column + h_margin/2, row_1, 0]; right_rib_x = width_mm - hole_dist_side - thickness; // draw panel, subtract.

New Pull Request

Labels Milestones