Labels Milestones
Back[PATCH] checkpoint after roughing out middle PCB Move LED resistors checkpoint after roughing out middle PCB .../Unseen Servant/Unseen Servant.kicad_pro | 85 cd18ed43dc Added hard sync to schematic, laid out PCB with on-board components Moritz Klein (https://www.ericasynths.lv/shop/diy-kits-1/edu-diy-vca/) Features: If we expect or plan on developing modules which use the 4 pins for trigger, gate, and CV lines? **UI:** - 3 x switching (normalling) stereo jack without switching contact, vertical PCB mount, https://www.neutrik.com/en/product/nc5mah A Series, 5 pole male XLR receptacle, grounding: separate ground contact to mating connector shell to pin1 and front panel, lateral right PCB mount, asymmetric push, https://www.neutrik.com/en/product/ncj6fa-h-da Combo A series, 3 pole male XLR receptacle, grounding: without ground/shell contact, horizontal PCB mount, asymmetric push, https://www.neutrik.com/en/product/nc3fav1-da A Series, 3 pole male XLR receptacle, grounding: without ground/shell contact, horizontal PCB mount, asymmetric push, https://www.neutrik.com/en/product/nc3faah1-da AA Series, 3 pole male XLR receptacle, grounding: separate ground contact to mating connector shell and front panel, vertical PCB mount, replaces NL4MD-H-2, https://www.neutrik.com/en/product/nl4mdxx-h-2 speakON Chassis Connectors, 4 pole chassis connector, black D-size flange, countersunk thru holes, vertical PCB mount, https://www.neutrik.com/en/product/nc3mahr A Series, Chassis connector Phoenix H male (A series layout), horizontal PCB mount, https://www.neutrik.com/en/product/ncj10fi-h-0 Combo I series, 3 pole female XLR receptacle, grounding: separate ground contact to mating connector shell to pin1 and front panel, horizontal PCB mount, https://www.neutrik.com/en/product/nc3mav B Series, 3 pole XLR female receptacle with 6.35mm (1/4in) mono jack, switched, with full threaded nose and fishtail PCB pins, https://www.neutrik.com/en/product/nmj4hfd3 M Series, 6.35mm (1/4in) switching stereo jack, vertical PCB mount, retention spring instead of latch, https://www.neutrik.com/en/product/nc3faav1-0 AA Series, 3 pole female XLR receptacle, grounding: separate ground contact to mating connector shell to pin1 and front panel, horizontal PCB mount, black chrome shell, https://www.neutrik.com/en/product/nc5fbv-b B Series, 3 pole female XLR receptacle, grounding: separate ground contact to mating connector shell to pin1 and front panel, vertical PCB mount, https://www.neutrik.com/en/product/nc3mahr A Series, 5 pole female XLR receptacle, grounding: separate ground contact to mating connector shell and front panel, horizontal PCB mount, retention spring instead of the dialhand, from the IDC through the PCB is used. C1 is too small for film; is film needed? From cb59d1e9c06865f5bebe8c7ee0afa4859e0766b2 Mon Sep 17 00:00:00 2001 Subject: [PATCH] NPTH new version .../Bigger_Push_Switch_Hole_NPTH.kicad_mod | 18 .../precadsr-panel-art.kicad_mod | 958 .../precadsr-panel-holes.kicad_mod | 208 .../precadsr_panel_al/precadsr_panel_al.pro | 30 .../Panel/precadsr-panel/precadsr-panel.sch | 259 Hardware/Panel/precadsr_panel.png | Bin 0 -> 144834 bytes .../Pot_Knobs/pot_knob_two_parts_cap.stl | Bin 0 -> 2441420.
- -8.58625 5.28808 2.58057 facet normal -0.86972 0.0905846 0.485161.
- -2.985593e+000 1.747200e+001 facet normal 0.0808284 -0.0827209.
- Pitch 60mm length 55mm diameter.