synth_tools

Back

Mode is ~$16-20 in parts, two tl074 op amps and otherwise a bunch of wires backwards .../Unseen Servant/Unseen Servant.kicad_sch | 551 Schematics/Unseen Servant/fp-info-cache glide in (sleeve and normal both GND - Gate out (could normal to Reset In socket Reset Socket to U3-3 = capacitor measurement roughly 15nF (has a resistor as well Once/Cont When in Cont mode shorts Casc Out normal to TP10, optional) - Casc out 2x Toggle Switches, 2pin: - all step switches (all go to same bus run/stop 2x Pushbutton switches, all 2pin: reset Pots, 3-pin: - Glide In - U1-13 (can get at from top when assembled Stop Switch - 10 - center_adjust; center_col = width_mm/2; row_1 = bottom_row + v_margin + 12; row_1 = v_margin+12; Experimenting with more panel layout ideas working_height = height - v_margin - title_font; left_rib_x = thickness * 1.2; right_rib_x = width_mm - hole_dist_side, height - hole_dist_top); cylinder(r=hole_r, h=thickness*2); echo("Putting a hole with radius: ", hole_r , " at ", hole_dist_side, height - v_margin - title_font; saw_out = [third_col, fourth_row, 0]; //Fifth row interface placement sync_in = [first_col, fourth_row, 0]; pwm_cv_lvl = [width_mm - h_margin - working_width/8, row_3, 0]; manual_2 = [left_col, row_6, 0]; cv_1b_atten = [right_col, row_7, 0]; manual_1 = [left_col, row_6, 0]; audio_in_1 = [left_col, row_5, 0]; cv_in_2a = [left_col, row_3, 0]; cv_in_2b = [right_col, row_7, 0]; cv_in_1b = [right_col, row_2, 0]; pwm_in = [width_mm - h_margin - working_width/8, row_3, 0]; manual_2 = [left_col, row_5, 0]; audio_out_1 = [right_col, row_7, 0]; manual_1 = [left_col, row_3, 0]; pwm_duty = [input_column, row_2, 0]; triangle_out = [width_mm-h_margin-working_width/4, row_1, 0]; saw_out = [h_margin + working_width/4, row_1, 0]; saw_out = [h_margin + working_width/4, row_1, 0]; pwm_in = [first_col, fifth_row, 0]; //left_rib_x = thickness * 1.2; right_rib_x = width_mm - thickness*2; // draw a "vertical" wall // h = shafthole_height, $fn = sphere_indents_faces); height = 128.5; // A little less then 3U // Thickness of module (HP width = 24; // [1:1:84] v_margin = hole_dist_top*2; left_rib_x = hole_dist_side + thickness; working_height = height - rail_clearance - thickness*2 - 16.5/2; // 16.5 is the diameter of the Stick // } // Chainsawsuit // Poorly Drawn Lines elseif (strpos($article["link"], "drugsandwires.fail/dnwcomic/") !== FALSE) { elseif (strpos($article['link'], 'cad-comic.com/cad/') !== FALSE) { elseif (strpos($article['link'], 'threepanelsoul.com/2') !== FALSE.

New Pull Request

Labels Milestones