Labels Milestones
BackGate Out - Diode from rotary pin 13 - CV Out - Diode from rotary pin 13? CV Out - 1K to U2-14 - Casc out 2x Toggle Switches, 2pin: all step switches (all go to same bus 2x Pushbutton switches, all 2pin: - all step switches (all go to same bus run/stop 2x Pushbutton switches, all 2pin: - all step switches (all go to same bus run/stop 2x Pushbutton switches, all 2pin: reset Pots, 3-pin: - Glide attenuator (B10k) (join two left pins from below Pots, 2-pin: - Glide, manual (A100k) (two left pins, from below) - Clock In - ~27K to U3-8? No, transistors maybe activate? - Clock Out - 1K to U3-7 Glide section not working right, just pegging the output jacks row_2 = row_1 + v_margin + 12; row_2 = row_1 + vertical_space/7; row_7 = row_6 + vertical_space/7; cv_in_1a = [left_col, row_2, 0]; fm_lvl = [h_margin+working_width/8, row_3, 0]; manual_2 = [left_col, row_6, 0]; cv_1b_atten = [right_col, row_1, 0]; triangle_out = [width_mm-h_margin-working_width/4, row_1, 0]; saw_out = [output_column, bottom_row, 0]; cv_in = [h_margin, row_1, 0]; square_out = [third_col, third_row, 0]; //Fourth row interface placement square_out = [third_col, fifth_row, 0]; pwm_duty = [width_mm - h_margin - working_width/8, row_4, 0]; pwm_cv_lvl = [width_mm - h_margin - working_width/8, row_3, 0]; cv_in_2b = [right_col, row_2, 0]; fm_lvl = [second_col, second_row, 0]; //Third row interface placement f_tune = [width_mm/2 + h_margin, top_row, 0]; f_tune = [h_margin+working_width/8, row_4, 0]; left_rib_x = hole_dist_side + thickness; working_height = height - v_margin - title_font_size*2; saw_out = [output_column, bottom_row, 0]; c_tune = [second_col, fourth_row, 0]; triangle_out = [output_column, row_2, 0]; square_out = [output_column, row_1, 0]; pwm_in = [width_mm - h_margin - working_width/8, row_2, 0]; fm_lvl = [second_col, second_row, 0]; //Third row interface placement fm_in = [h_margin+working_width/8, row_4, 0]; pwm_cv_lvl = [second_col, third_row, 0]; fm_in = [first_col, third_row, 0]; fm_in = [h_margin+working_width/8, row_3, 0]; pwm_duty = [width_mm - h_margin - working_width/8, row_2, 0]; cv_2b_atten = [right_col, row_2, 0]; triangle_out = [third_col, fourth_row, 0]; //Fifth row interface placement f_tune = [width_mm/2 + h_margin, top_row, 0]; f_tune = [width_mm/2 - h_margin, top_row, 0]; f_tune = [width_mm/2 + h_margin, top_row, 0]; f_tune = [second_col, first_row, 0]; c_tune = [second_col, fifth_row, 0]; pwm_duty = [width_mm - h_margin - working_width/8, row_3, 0]; right_rib_x = width_mm - h_margin; input_column = h_margin; col_right = width_mm - thickness*2; union() { z_position .
New Pull Request