Labels Milestones
BackLayout 2x Sockets, all three pins need wires: glide in (sleeve and normal both GND 6x Sockets, 2pin: - all step switches (all go to same bus run/stop 2x Pushbutton switches, all 2pin: - all step switches (all go to 10 Alternative: Midi -> CV We could generate CV some other way for now, such as: ** https://www.mouser.com/ProductDetail/Bourns/PTL30-15O0-105A2?qs=fV9UsjselOEqdQiKFAm%2Fog%3D%3D (A1M, orange LED, 30mm travel, 15mm shaft) * https://www.mouser.com/ProductDetail/Bourns/PTL30-15R0-103B1?qs=X8nz4ozed5glbMOCRmYKzw%3D%3D (B10K, red LED, 30mm travel, 15mm shaft https://www.digikey.com/en/products/detail/bourns-inc/PTL30-15R0-103B1/3781301 (red B10K) and https://www.digikey.com/en/products/detail/bourns-inc/PTL30-15O0-105A2/7314942 (orange A1M * The SPDT toggle switch ON-ON | | | | | | | R20, R22 | 2 jackHoleDepth = 10; // [1:1:84] //Second row interface placement fm_in = [input_column + h_margin/2, row_1, 0]; fm_pot = [input_column + h_margin/2, bottom_row, 0]; fm_in = [input_column - h_margin/2, bottom_row, 0]; c_tune = [width_mm/2 + h_margin, top_row, 0]; left_rib_x = 0; // (2) FIXED AND DERIVED MEASURES // Prevent anything following from showing up as Customizer parameters. /* [Hidden] */ // Degree of detail * and/or take a look to the Covered Software is with You. For purposes of this License to the extent necessary to make fitting inside a case easier. Or 10mm if it can fit; losing the bodge area. Assembly Tests: Glide In - ~27K to U3-8? No, transistors maybe activate? Outs: Clock Out - 1K to U3-7 Glide section not working right, just pegging the output jacks output_column = width_mm - 10 - center_adjust; center_col = width_mm/2; vertical_space = height - v_margin*2 - title_font_size; working_increment = working_height / (8+tolerance/5); // generally-useful spacing amount for vertical columns of stuff col_left = thickness * 2; right_rib_x = width_mm - thickness*2.2; left_rib_x = thickness * 1; //right_rib_x = width_mm - col_right - thickness; // column from edge plus hole radius // mounting holes 47.1mm, see https://disti-assets.s3.amazonaws.com/tonar/files/datasheets/16730.pdf 9-pin D-Sub connector, horizontal/angled (90 deg), THT-mount, male, pitch 2.77x2.84mm, pin-PCB-offset 4.9399999999999995mm, distance of mounting holes to PCB edge 15.979999999999999mm, see https://disti-assets.s3.amazonaws.com/tonar/files/datasheets/16730.pdf 26-pin D-Sub connector, horizontal/angled (90 deg), THT-mount, female, pitch 2.77x2.84mm, pin-PCB-offset 9.4mm, see http://docs-europe.electrocomponents.com/webdocs/1585/0900766b81585df2.pdf 25-pin D-Sub connector, horizontal/angled (90 deg), THT-mount, female, pitch 2.29x2.54mm, pin-PCB-offset 9.4mm, see http://docs-europe.electrocomponents.com/webdocs/1585/0900766b81585df2.pdf 9-pin D-Sub connector, horizontal/angled (90 deg), THT-mount, male, pitch 2.77x2.84mm, pin-PCB-offset 14.56mm, distance of mounting holes 33.3mm, see https://disti-assets.s3.amazonaws.com/tonar/files/datasheets/16730.pdf 15-pin D-Sub connector, horizontal/angled (90 deg), THT-mount, female, pitch 2.29x2.54mm, pin-PCB-offset 9.4mm, see http://docs-europe.electrocomponents.com/webdocs/1585/0900766b81585df2.pdf 44-pin D-Sub connector, horizontal/angled (90 deg), THT-mount, female, pitch 2.77x2.84mm, pin-PCB-offset 14.56mm, distance of mounting holes to PCB edge 9.12mm, see https://disti-assets.s3.amazonaws.com/tonar/files/datasheets/16730.pdf 25-pin D-Sub connector, horizontal/angled (90 deg), THT-mount, female, pitch 2.77x2.84mm, pin-PCB-offset.
New Pull Request