Labels Milestones
Back| A-1138 | | | | | R14, R15, R18 | 3 | 10k | Resistor | | | | | | C4, C5 | 2 | 1M | Resistor | | | Tayda | A-553 | | | C12 | 1 Kosmo_panel | 1 | 2_pin_Molex_connector | KK254 Molex header 2.54 mm spacing Q1, Q2, Q3, Q4, Q5 R1, R2, R23, R24 | 4 | 100k | Resistor | | | Tayda | A-826 | | | | | | | Tayda | A-1847 | | | 4 Schematics/LUTHERS_VCO.diy Executable file View File Panels/FireballSpell.png Executable file Unescape Fireball/Fireball_panel.kicad_dru Normal file Unescape threeUHeight = 133.35; //overall 3u height panelInnerHeight = 110; //rail clearance = ~11.675mm, top and bottom boards. Final work on PCB with exploratory 8hp layout 2x Sockets, all three pins need wires: - clk in - glide in (sleeve and normal both GND 6x Sockets, 2pin: - all step switches (all go to same bus) - run/stop 2x Pushbutton switches, all 2pin: reset Pots, 3-pin: - Glide attenuator (B10k) (join two left pins from below Clock rate goes down when resistance goes up, opposite to expectation. C1 is too small for a single 0.1 mm² wires, basic insulation, conductor diameter 0.65mm, outer diameter 3.9mm, size source Multi-Contact FLEXI-E 1.0 (https://ec.staubli.com/AcroFiles/Catalogues/TM_Cab-Main-11014119_(en)_hi.pdf), bend radius 3 times outer diameter, generated with kicad-footprint-generator Soldered wire connection with feed through strain relief, for 5 times 1 mm² wires, basic insulation, conductor diameter 1.7mm, outer diameter 3.9mm, size source Multi-Contact FLEXI-E 1.5 (https://ec.staubli.com/AcroFiles/Catalogues/TM_Cab-Main-11014119_(en)_hi.pdf), bend radius 3 times outer diameter, generated with kicad-footprint-generator JST SH top entry JST XA series connector, SM13B-SRSS-TB (http://www.jst-mfg.com/product/pdf/eng/eSH.pdf), generated with kicad-footprint-generator Mounting Hardware, inside blind hole M1.6, height 2, Wuerth electronics 9774080960 (https://katalog.we-online.de/em/datasheet/9774080960.pdf,), generated with kicad-footprint-generator Samtec HLE .100" Tiger Beam Cost-effective Single Beam Socket Strip, HLE-109-02-xxx-DV-LC, 9 Pins per row (http://suddendocs.samtec.com/prints/hle-1xx-02-xxx-dv-xx-xx-xx-mkt.pdf, http://suddendocs.samtec.com/prints/hle-dv-footprint.pdf), generated with kicad-footprint-generator Inductor SMD 0201 (0603 Metric), square (rectangular) end terminal, IPC_7351 nominal, (Body size from: http://datasheets.avx.com/AVX-HV_MLCC.pdf), generated with kicad-footprint-generator Molex MicroClasp Wire-to-Board System, 55935-0930, 9 Pins (http://www.farnell.com/datasheets/2157639.pdf), generated with kicad-footprint-generator Samtec HLE .100.
- 4.18518 -5.59382 7.89166 facet normal 0.247514 0.963781.
- Type-C USB3 receptacle SMD USB Micro-B receptacle, horizontal.
- Width 2.54mm Resistor, Box series, Radial, pin pitch=5.00mm.