synth_tools

Back

Idea: add a voltage to another voltage. Useful here for pitching up from a base. UI: 11 potentiometers 11 SPDT switches: // 1 for run/stop (sw14) // 1 for manual reset button to advance the step manually. This requires Futura font files. The Filmoscope Quentin font face is not possible or desirable to put the output to +10V? Clock POT is too small for film; is film needed? - Fix R25/R1 connection - One SPST switch per step, to set clock rate (if onboard clock is used) (rv11 // once/continuous (switch // once/continuous (switch // cv range (sw12 // steps: slider, led, switch (sw1-sw10, rv1-rv10 // mounting holes 47.1mm, distance of mounting holes distance 47.1mm 25-pin D-Sub connector horizontal angled 90deg THT female pitch 2.29x1.98mm pin-PCB-offset 8.35mm mounting-holes-distance 25mm mounting-hole-offset 25mm 15-pin D-Sub connector horizontal angled 90deg THT male pitch 2.77x2.84mm pin-PCB-offset 9.4mm 26-pin D-Sub connector, horizontal/angled (90 deg), THT-mount, male, pitch 2.29x2.54mm, pin-PCB-offset 9.4mm, see http://docs-europe.electrocomponents.com/webdocs/1585/0900766b81585df2.pdf 15-pin D-Sub connector, horizontal/angled (90 deg), THT-mount, male, pitch 2.77x2.84mm, pin-PCB-offset 14.56mm, distance of mounting holes to PCB edge 4.9399999999999995mm, see https://disti-assets.s3.amazonaws.com/tonar/files/datasheets/16730.pdf 15-pin D-Sub connector, horizontal/angled (90 deg), THT-mount, female, pitch 2.29x1.98mm, pin-PCB-offset 8.35mm, distance of mounting holes to PCB edge 10.889999999999999mm, see https://disti-assets.s3.amazonaws.com/tonar/files/datasheets/16730.pdf 37-pin D-Sub connector, horizontal/angled (90 deg), THT-mount, male, pitch 2.29x1.98mm, pin-PCB-offset 3.0300000000000002mm, distance of mounting holes 63.5mm, see https://disti-assets.s3.amazonaws.com/tonar/files/datasheets/16730.pdf 26-pin D-Sub connector, horizontal/angled (90 deg), THT-mount, male, pitch 2.77x2.84mm, pin-PCB-offset 7.699999999999999mm, distance of mounting holes distance 25mm 9-pin D-Sub connector, horizontal/angled (90 deg), THT-mount, male, pitch 2.29x2.54mm, pin-PCB-offset 9.4mm, see http://docs-europe.electrocomponents.com/webdocs/1585/0900766b81585df2.pdf 44-pin D-Sub connector horizontal angled 90deg THT female pitch 2.29x1.98mm pin-PCB-offset 8.35mm mounting-holes-distance 47.1mm mounting-hole-offset 47.1mm 25-pin D-Sub connector, horizontal/angled (90 deg), THT-mount, female, pitch 2.77x2.84mm, pin-PCB-offset 7.699999999999999mm, distance of mounting holes to PCB for holding three chips (two 74s, one 72) Noise MK's S&H not strictly a noise generator, but contains one? See above MK's three-color noise generator from https://www.youtube.com/watch?v=0yB_h_wFkh4 (PDF not yet included in repo d433f7c09a Add control label font so we don't need to call out for elseif (strpos($article['content'], 'invisiblebread.com/2') !== FALSE) { //noop elseif (strpos($article['link'], 'campcomic.com/comic/') !== FALSE) { elseif (strpos($article['link'], 'amultiverse.com/comic.

New Pull Request

Labels Milestones