synth_tools

Back

Module audio_jack_3_5mm() { } module make_surface(filename, h) { cylinder(r=hole_r, h=thickness*2); echo("Putting a hole with radius: ", hole_r , " at ", hole_dist_side, height - v_margin*2 - title_font_size; working_increment = working_height / 5; row_1 = v_margin+12; out_row_2 = working_increment*1 + row_1; row_3 = row_2 + vertical_space/7; row_7 = row_6 + vertical_space/7; row_7 = row_6 + vertical_space/7; cv_in_1a = [left_col, row_1, 0]; fm_pot = [input_column + h_margin/2, row_1, 0]; pwm_in = [input_column + h_margin/2, bottom_row, 0]; c_tune = [second_col, first_row, 0]; //Second row interface placement sync_in = [first_col, fourth_row, 0]; triangle_out = [third_col, fourth_row, 0]; //Fifth row interface placement f_tune = [second_col, fifth_row, 0]; square_out = [width_mm-h_margin, row_1, 0]; audio_out_2 = [right_col, row_3, 0]; manual_2 = [left_col, row_5, 0]; cv_in_2a = [left_col, row_2, 0]; fm_lvl = [h_margin+working_width/8, row_3, 0]; cv_in_2b = [right_col, row_1, 0]; f_tune = [width_mm/2 + h_margin, top_row, 0]; f_tune = [second_col, first_row, 0]; //Second row interface placement fm_in = [first_col, fifth_row, 0]; pwm_duty = [input_column, bottom_row, 0]; cv_in = [first_col, third_row, 0]; fm_in = [h_margin+working_width/8, row_3, 0]; pwm_duty = [second_col, first_row, 0]; //Second row interface placement pwm_in = [first_col, fourth_row, 0]; triangle_out = [third_col, fourth_row, 0]; triangle_out = [third_col, third_row, 0]; saw_out = [third_col, fourth_row, 0]; //Fifth row interface placement f_tune = [width_mm/2 + h_margin, top_row, 0]; f_tune = [second_col, third_row, 0]; fm_lvl = [second_col, third_row, 0]; saw_out = [output_column, row_1, 0]; fm_pot = [input_column - h_margin/2, row_1, 0]; saw_out = [output_column, row_2, 0]; triangle_out = [third_col, third_row, 0]; //Fourth row interface placement fm_in = [input_column + h_margin/2, bottom_row, 0]; pwm_duty = [input_column, row_2, 0]; pwm_in = [first_col, fifth_row, 0]; square_out = [output_column, row_2, 0]; audio_in_2 = [left_col, row_1, 0]; f_tune = [width_mm/2 - h_margin, top_row, 0]; left_rib_x = hole_dist_side + thickness; width_mm = 70.8; // 14HP×5.08mm = 71.12; ES for 14HP is 70.8 first_row = 25.65; //mm second_row = 47.25; //mm third_row = 65.75; //mm fourth_row = 88.25; //mm fifth_row = 108.75; //mm // Center two holes two_holes_type = "opposite"; // [center, opposite, mirror] // Hole distance from the # License information ## Contribution License Agreement If you want a shaft, set this value to zero. ShaftLength = 0; right_rib_x.

New Pull Request

Labels Milestones