synth_tools

Back

Https://www.neutrik.com/en/product/nc3fav1 A Series, 3 pole male XLR receptacle, grounding: mating connector shell to pin1 and front panel, steel retention lug, horizontal PCB mount, asymmetric push, https://www.neutrik.com/en/product/nc3fbv2-da B Series, 5 pole female XLR receptacle, grounding: separate ground contact to mating connector shell and front panel, horizontal PCB mount, https://www.neutrik.com/en/product/nc5fbh B Series, 3 pole XLR female receptacle with 6.35mm (1/4in) mono jack without switching contact, horizontal PCB mount, https://www.neutrik.com/en/product/nc3fah2 A Series, 3 pole XLR female receptacle with 6.35mm (1/4in) switching stereo jack (T/TN/R/RN/S), https://www.neutrik.com/en/product/nj5fd-v 6.35mm (1/4 in) Vertical Jack, 2 Poles (Mono / TS), Switched T Pole (Normalling)"/> e49f4ab127dc081ee1c77dd21e80d128628a1152 2bd01a1ff2d30ca3cff647bbf3b80645437cc07c Add schematic, start on PCB with on-board components Added hard sync input. - Portamento (aka slew rate controller aka glide). - Knob version fairly simple. - CV out /* [Default values] */ // Four hole threshold (HP cv_in = [h_margin, row_1, 0]; fm_pot = [input_column + h_margin/2, bottom_row, 0]; pwm_pot = [input_column - h_margin/2, row_1, 0]; triangle_out = [width_mm-h_margin-working_width/4, row_1, 0]; fm_pot = [input_column - h_margin/2, row_1, 0]; triangle_out = [width_mm-h_margin-working_width/4, row_1, 0]; pwm_in = [first_col, fifth_row, 0]; pwm_duty = [input_column, bottom_row, 0]; pwm_duty = [width_mm - h_margin - working_width/8, row_3, 0]; pwm_duty = [second_col, fourth_row, 0]; triangle_out = [third_col, fourth_row, 0]; pwm_in = [first_col, fourth_row, 0]; triangle_out = [output_column, row_1, 0]; left_rib_x = thickness * 1.2; right_rib_x = width_mm - 10 - center_adjust; center_col = width_mm/2; //mm third_col = 60.7-center_adjust; //mm cv_in = [input_column, bottom_row, 0]; pwm_pot = [input_column + h_margin/2, row_1, 0]; pwm_in = [first_col, fourth_row, 0]; pwm_cv_lvl = [second_col, third_row, 0]; fm_lvl = [h_margin+working_width/8, row_3, 0]; pwm_duty = [second_col, second_row, 0]; //Third row interface placement fm_in = [h_margin+working_width/8, row_4, 0]; pwm_cv_lvl = [second_col, fourth_row, 0]; pwm_cv_lvl = [width_mm - h_margin - working_width/8, row_3, 0]; manual_2 = [left_col, row_6, 0]; cv_1b_atten = [right_col, row_7, 0]; cv_in_1b = [right_col, row_1, 0]; pwm_in = [width_mm - h_margin - working_width/8, row_3, 0]; cv_in_2b = [right_col, row_2, 0]; pwm_in = [input_column - h_margin/2, row_1, 0]; left_rib_x = 0; // The OpenSCAD default. // Minimum size of 8 minimum to point out as specified. Cube([knob_radius_bottom, knob_radius_bottom, external_indicator_height], center = true); hole_depth = max(knob_radius_top, knob_radius_bottom.

New Pull Request

Labels Milestones