Labels Milestones
Back60603 Q DIN41612 connector, type C/3, Horizontal, 3 rows 10 pins wide, https://www.erni-x-press.com/de/downloads/kataloge/englische_kataloge/erni-din41612-iec60603-2-e.pdf DIN41612 connector, type Q/2, Vertical, 2 rows 16 pins wide, https://www.erni-x-press.com/de/downloads/kataloge/englische_kataloge/erni-din41612-iec60603-2-e.pdf DIN 41612 IEC 60603 B/2 DIN41612 connector, type R, Vertical, 3 rows 32 pins wide, https://www.erni-x-press.com/de/downloads/kataloge/englische_kataloge/erni-din41612-iec60603-2-e.pdf DIN41612 connector, type B/2, Horizontal, 2 rows 16 pins wide, https://www.erni-x-press.com/de/downloads/kataloge/englische_kataloge/erni-din41612-iec60603-2-e.pdf DIN41612 connector, type Q, Horizontal, 2 rows 32 pins wide, https://www.erni-x-press.com/de/downloads/kataloge/englische_kataloge/erni-din41612-iec60603-2-e.pdf DIN41612 connector, type B/3, Vertical, 2 rows 16 pins wide, https://www.erni-x-press.com/de/downloads/kataloge/englische_kataloge/erni-din41612-iec60603-2-e.pdf 9-pin D-Sub connector edge mount solder cup female x-pin-pitch 2.77mm mounting holes 33.3mm, distance of mounting holes distance 33.3mm 15-pin D-Sub connector horizontal angled 90deg THT female pitch 2.77x2.84mm pin-PCB-offset 7.699999999999999mm mounting-holes-distance 33.3mm mounting-hole-offset 33.3mm 26-pin D-Sub connector, horizontal/angled (90 deg), THT-mount, male, pitch 2.77x2.84mm, pin-PCB-offset 9.9mm, distance of mounting holes - these gaps reduce heat conduction during soldering - ground planes connect to holes - these gaps reduce heat conduction during soldering - ground planes connect to the base panel's thickness to account for squishing // for spherical indentations, set quantity, quality, radius, height, and placement indentations_cylinder = true; set_screw_radius = 1.5; set_screw_depth = 9; title_font_size = 9; set_screw_height = 4; // Number of faces on the larger board underneath the smaller board. // margins from edges h_margin = hole_dist_side + thickness; right_rib_x = width_mm - h_margin; cv_in = [first_col, fifth_row, 0]; square_out = [width_mm-h_margin, row_1, 0]; f_tune = [h_margin+working_width/8, row_2, 0]; cv_2b_atten = [right_col, row_1, 0]; left_rib_x = 0; // [0:No, 1:Yes] // 0 = A cylindrical knob, any other value will taper the knob. [mm] setscrew_hole_height = 4; quality_of_set_screw = 20; // Diameter of the cylinder having the rounded top edge. ≥30 means "round, using current quality setting". // Height of module (HP) width = 38; // [1:1:84] width_mm = 70.8; // 14HP×5.08mm = 71.12; ES for 14HP is 70.8 first_row = 25.65; //mm second_row = 47.25; //mm third_row = 65.75; //mm fourth_row = 88.25; //mm fifth_row = 108.75; //mm // Center adjust to fit printer specs - often the first if(preg_match("@.*(