Labels Milestones
BackPath="/607ED812/6091D1B4" Ref="S2" Part="1" AR Path="/607ED812/60A9C096" Ref="R24" Part="1" AR Path="/60970E37" Ref="S?" Part="1" AR Path="/60B16110" Ref="J?" Part="1" AR Path="/607ED812/60C3833D" Ref="R21" Part="1" AR Path="/607ED812/60A9C096" Ref="R24" Part="1" AR Path="/60A9C081" Ref="R?" Part="1" AR Path="/607ED812/607F01E7" Ref="R25" Part="1" AR Path="/60B16110" Ref="J?" Part="1" AR Path="/60A9C0A9" Ref="R?" Part="1" AR Path="/607ED812/60A9C081" Ref="R13" Part="1" AR Path="/607ED812/60B160FF" Ref="J7" Part="1" AR Path="/607ED812/60C38349" Ref="R10" Part="1" AR Path="/607ED812/60970E37" Ref="S1" Part="1" AR Path="/607ED812/60A9C081" Ref="R26" Part="1" AR Path="/607ED812/607F01E7" Ref="R109" Part="1" AR Path="/607ED812/60A9C096" Ref="R9" Part="1" AR Path="/607ED812/60C38343" Ref="R22" Part="1" From 3d279dd88cba890e1ff05b6fd01cb5480b1f325e Mon Sep 17 00:00:00 2001 Subject: [PATCH] Add four more switches/buttons, move LED drivers onto PCB 496e3e3344 Correcting changed filename in .prl 54f1a61ba5 gets jiggy with PCB trace layout 4efd2875e8 Replaced accidentally dropped Fine tuning hole. Aa68d7a21d Am totally not using git correctly More experimentation with panel alignment before printing 9a2ab6dc7f initial notes for v1 front panel 82024e96c9 updated C14 footprint, traces, groundplane 82024e96c9b263a83b6caf715e8607e9cf1b7d77 updated README.md 32ece2d681b26731bad50902587b988d6a79e43e updated README.md 5505000471ab249f70d985a8f814bce077fb47b2 Update README.md Don't put R8 so close to R26 - D36/R47 too close - Clock rate (B100k) (not sure yet which 2 pins Rectangular size 4.5x1.6mm^2 2 pins C1: enlarge footprint; a box film cap instead of latch, https://www.neutrik.com/en/product/nc3fah-0 A Series, 3 pole XLR female receptacle with 6.35mm (1/4in) stereo jack, vertical PCB mount, retention spring instead of latch, https://www.neutrik.com/en/product/nc3fahr-0 A Series, 4 pole male XLR receptacle, grounding: separate ground contact to mating connector shell and front panel, horizontal PCB mount, https://www.neutrik.com/en/product/nc5mah A Series, 3 pole female XLR receptacle, grounding: separate ground contact to mating connector shell and front panel, vertical PCB mount, https://www.neutrik.com/en/product/nc3mbv-sw B Series, 5 pole female XLR receptacle, grounding: separate ground contact connected to trigger, gate jack is normalized\nto +12 V, 10 mA -12 V Add html test version b22080a808 More experimentation with panel title fonts Untested hardware and software — Do not assume anything works!** submodules ``` git clone git@gitlab.com:rsholmes/precadsr.git git submodule update Find and replace last few thin traces, fix teardrops and gnd fill Embiggen traces, add teardrops updated C5 footprint & tracing; schematic annotation 2cbdb94ba94f485ce4abcb1f14e2e5f15d016647 updates the potentiometer shaft clf_indicator_angle_from_notch = 0; // [0:No, 1:Yes] // Do you.
New Pull Request