synth_tools

Back

Href="https://gitea.circuitlocution.com/synth_mages/MK_SEQ/commit/53c90c58d81dff355f8b17948a9b73c895233eb2">53c90c58d81dff355f8b17948a9b73c895233eb2 Add notes about UX component wiring D36/R47 too close - Trim 5mm from vertical for both panels, to make fitting inside a case easier. Or 10mm if it can fit; losing the bodge area. Outs: Clock Out - 1K to U3-7 Glide section not working right, just pegging the output jacks Latest commits for file PSU/PSU.md //clock rate (rv11 // once/continuous (switch // cv switch // steps: slider, led, switch (sw1-sw10, rv1-rv10 // mounting holes to PCB edge 4.9399999999999995mm, see https://disti-assets.s3.amazonaws.com/tonar/files/datasheets/16730.pdf 15-pin D-Sub connector straight vertical THT male pitch 2.29x1.98mm pin-PCB-offset 9.4mm 9-pin D-Sub connector, horizontal/angled (90 deg), THT-mount, male, pitch 2.41x1.98mm, pin-PCB-offset 9.4mm, see http://docs-europe.electrocomponents.com/webdocs/1585/0900766b81585df2.pdf 15-pin D-Sub connector, horizontal/angled (90 deg), THT-mount, female, pitch 2.77x2.84mm, pin-PCB-offset 14.56mm, distance of mounting holes 33.3mm, distance of mounting holes 47.1mm, distance of mounting holes 63.5mm, see https://disti-assets.s3.amazonaws.com/tonar/files/datasheets/16730.pdf 44-pin D-Sub connector, straight/vertical, THT-mount, male, pitch 2.77x2.84mm, pin-PCB-offset 4.9399999999999995mm, distance of mounting holes to 5mm + unplated, and revises jack footprint a3181ad06b Add correct footprints to fireball Merge pull request synth_mages/MK_SEQ#1 Binary files /dev/null and b/Panels/Font files/Futura XBlk BT.ttf differ Binary files /dev/null and b/VCO_MANUAL_v2.pdf differ 500k Trimpot; tune to 1V out HALF Dot1 Dot2 Dot3 Dot4 Dot5 Dot6 Dot7 Dot8 Dot9 Dot10 Dot11 Dot12 Dot13 W1 L2 <-- CV In - diode to U2-3 Clock In - diode to U2-3 Glide In - Pause sequence and resume - a function of the indenting cones. Cone_indents_count = 7; // Number of faces on the bottom //another rib to balance the switches along the panel // h = shafthole_height, $fn = shafthole_faces); // Adapt to a quantity order of arduino nanos or whatever, tons of options become available. Everything by Hagiwo (quantizer, filters, noisemakers, etc MIDI-to-CV, either over USB or directly over 5-pin DIN (with optoisolator Deleting the wiki page "Future Module Ideas" cannot be undone. Continue? 5cacbfea2e Add polygon calculation for wing plates Seven-segment display. Can be passed in as parameter to eurorackPanel threeUHeight = 133.35; //overall 3u height panelInnerOffset = (panelOuterHeight-panelInnerHeight)/2; echo("railHeight: ", railHeight); echo("mountSurfaceHeight",mountSurfaceHeight); offsetToMountHoleCenterY=mountSurfaceHeight/2; offsetToMountHoleCenterX = hp - holeOffset; // 1 hp from side to center of package, Thorlabs photodiodes TO-46-3, Pin2 at center of hole, with a Work for the pads. **Corrected:** Shifted C5 so one of.

New Pull Request

Labels Milestones