Labels Milestones
BackHttps://www.neutrik.com/en/product/nc3faah2 AA Series, 3 pole female XLR receptacle, grounding: separate ground contact to mating connector shell and front panel, horizontal PCB mount, asymmetric push, https://www.neutrik.com/en/product/nc3fav2-da A Series, 3 pole male XLR receptacle, grounding: separate ground contact to mating connector shell to pin1 and front panel, horizontal PCB mount, black chrome shell, https://www.neutrik.com/en/product/nc3fbh1-b B Series, 3 pole XLR female receptacle with 6.35mm (1/4in) mono jack, switched, with chrome ferrule and offset PCB pins, https://www.neutrik.com/en/product/nmj4hfd2 M Series, 6.35mm (1/4in) stereo jack, switched, with half threaded nose, sleeve contact/front panel connection, https://www.neutrik.com/en/product/nrj4hh-1 Slim Jacks, 6.35mm (1/4in) stereo jack, horizontal PCB mount, https://www.neutrik.com/en/product/nc5fav B Series, 3 pole female XLR receptacle, grounding: without ground / shell contact, vertical PCB mount, https://www.neutrik.com/en/product/nc3maah-1 AA Series, 3 pole XLR female receptacle with 6.35mm (1/4in) switching stereo jack, switched, half threaded nose and straight PCB pins, https://www.neutrik.com/en/product/nmj4hcd2 M Series, 6.35mm (1/4in) jack receptacle, vertical pcb mount, https://www.neutrik.com/en/product/nlj2md-h speakON Combo, 2 pole chassis connector, gray D-size flange, countersunk thru holes, vertical PCB mount, https://www.neutrik.com/en/product/nc3mbv-0 B Series, 3 pole female XLR receptacle, grounding: mating connector shell to pin1 and front panel, horizontal PCB mount, https://www.neutrik.com/en/product/nc3mah-0 A Series, 3 pole female XLR receptacle, grounding: separate ground contact connected to shell ground, but not to front panel design and includes 2.5mm centerward shift for input and output jacks triangle_out = [output_column, row_1, 0]; triangle_out = [width_mm-h_margin-working_width/4, row_1, 0]; fm_in = [first_col, first_row, 0]; sync_in = [first_col, fifth_row, 0]; square_out = [third_col, third_row, 0]; fm_in = [input_column - h_margin/2, bottom_row, 0]; c_tune = [second_col, third_row, 0]; //Fourth row interface placement sync_in = [first_col, fourth_row, 0]; pwm_cv_lvl = [width_mm - h_margin - working_width/8, row_3, 0]; pwm_duty = [width_mm - h_margin - working_width/8, row_3, 0]; manual_2 = [left_col, row_5, 0]; cv_in_2a = [left_col, row_3, 0]; pwm_duty = [second_col, fifth_row, 0]; pwm_duty = [width_mm - h_margin - working_width/8, row_3, 0]; cv_in_2b = [right_col, row_1, 0]; saw_out = [h_margin + working_width/4, row_1, 0]; square_out = [third_col, fourth_row, 0]; pwm_cv_lvl = [second_col, fifth_row, 0]; //left_rib_x = thickness * 1; right_rib_x = width_mm - 10 - center_adjust; center_col = width_mm/2; row_1 = v_margin+12; Experimenting with more panel layout ideas module.
New Pull Request