Labels Milestones
BackThe shaft, you can use it instead of latch, https://www.neutrik.com/en/product/nc3fahr2-0 A Series, 3 pole XLR female receptacle with 6.35mm (1/4in) stereo jack without switching contact, vertical PCB mount, https://www.neutrik.com/en/product/nc3mbv-sw B Series, 3 pole XLR female receptacle with 6.35mm (1/4in) mono jack, switched, with chrome ferrule and straight PCB pins, https://www.neutrik.com/en/product/nmj4hcd2 M Series, 6.35mm (1/4in) mono jack, switched, with full threaded nose and offset PCB pins, https://www.neutrik.com/en/product/nmj4hfd3 M Series, 6.35mm (1/4in) stereo jack, horizontal PCB mount, retention spring, https://www.neutrik.com/en/product/ncj9fi-v Combo I series, 3 pole female XLR receptacle, grounding: mating connector shell and front panel, steel retention lug, vertical PCB mount, replaces NL4MD-H-2, https://www.neutrik.com/en/product/nl4mdxx-h-2 speakON Chassis Connectors, 2 pole combination of speakON socket and 6.35mm (1/4in) mono jack, switched, with half threaded nose, sleeve contact/front panel connection, https://www.neutrik.com/en/product/nrj6hh-1 Slim Jacks, 6.35mm (1/4in) mono jack without switching contact, vertical PCB mount, asymmetric push, https://www.neutrik.com/en/product/nc3fah2-da A Series, 4 pole chassis connector, black D-size flange, countersunk thru holes, vertical PCB mount, https://www.neutrik.com/en/product/nl4md-v-1 speakON Chassis Connectors, 8 pole chassis connector, grey D-size flange, countersunk thru holes, vertical PCB mount, https://www.neutrik.com/en/product/nl4md-h-2 speakON Chassis Connectors, 4 pole male XLR receptacle, grounding: separate ground contact to mating connector shell and front panel. I adjusted the height about right. It's easier to adjust CV output range, switch between 5v and 2.5v max (or whatever is configured). Momentary-normal-off pushbutton to manually reset. LEDs: One per step, to set clock rate (if onboard clock is used) (rv11 // 1 rotary switch, 5+ positions - 10 LEDs 3 sockets Potentiometers: One potentiometer per step, to set output voltages. (10) One potentiometer for internal clock rate. Schematics/Unseen Servant/fp-info-cache Normal file Unescape BeginCmp TimeStamp = /551D9432; Reference = P6; ValeurCmp = CONN_1; IdModule = Socket_Arduino_Nano:1pin_Nano; EndCmp BeginCmp TimeStamp = /551D9432; Reference = P2; ValeurCmp = Digital; IdModule = Socket_Arduino_Nano:1pin_Nano; EndCmp BeginCmp TimeStamp = /551D9496; Reference = P6; ValeurCmp = CONN_1; IdModule = Socket_Arduino_Nano:1pin_Nano; EndCmp BeginCmp TimeStamp = /551D9432; Reference = P1; ValeurCmp = CONN_1; IdModule = Socket_Arduino_Nano:Socket_Strip_Arduino_1x15; EndCmp BeginCmp TimeStamp = /551D9466; Reference = P5; ValeurCmp = Digital; IdModule = Socket_Arduino_Nano:1pin_Nano; EndCmp BeginCmp TimeStamp = /551D9414; Reference = P2; ValeurCmp = CONN_1; IdModule = Socket_Arduino_Nano:1pin_Nano; EndCmp BeginCmp TimeStamp = /551D94EF; Reference = P1; ValeurCmp = CONN_1; IdModule = Socket_Arduino_Nano:Socket_Strip_Arduino_1x15; EndCmp BeginCmp TimeStamp = /551D9432; Reference = P6; ValeurCmp = CONN_1; IdModule = Socket_Arduino_Nano:1pin_Nano; EndCmp BeginCmp TimeStamp = /551D9432; Reference = P2; ValeurCmp = CONN_1; IdModule = Socket_Arduino_Nano:1pin_Nano; EndCmp Hardware/PCB/precadsr/precadsr.kicad_pcb Normal file.
New Pull Request