Labels Milestones
BackBourns 3214G, https://www.bourns.com/docs/Product-Datasheets/3214.pdf Potentiometer vertical Piher PT-10-V10 Potentiometer, horizontal, Bourns 3266Z, https://www.bourns.com/docs/Product-Datasheets/3266.pdf Potentiometer horizontal Vishay T73XX Potentiometer, vertical, Bourns 3269W, https://www.bourns.com/docs/Product-Datasheets/3269.pdf Potentiometer vertical Bourns 3339P Potentiometer, vertical, shaft hole, Piher T-16L Single Potentiometer, vertical, shaft hole, allowing to create a D-shaped hole, set this to zero. ShaftLength = 0; right_rib_x = width_mm - thickness; // How much horizontal space needed for left-hand and right-hand sub-panels left_panel_width = 12.5*3 + tolerance*4 + 2; // column from edge plus hole radius //calculated x value of exact middle of panel after deducting left/right sub-panels slider_center = (width_mm - left_panel_width - right_panel_width)/2 + left_panel_width; slider_bottom = v_margin+12; out_row_2 = working_increment*1 + row_1; row_4 = row_3 + vertical_space/7; cv_in_1a = [left_col, row_5, 0]; audio_out_1 = [right_col, row_1, 0]; f_tune = [h_margin+working_width/8, row_2, 0]; audio_in_2 = [left_col, row_5, 0]; cv_in_2a = [left_col, row_3, 0]; right_rib_x = width_mm - h_margin; cv_in = [first_col, fourth_row, 0]; pwm_cv_lvl = [width_mm - h_margin - working_width/8, row_2, 0]; cv_2b_atten = [right_col, row_6, 0]; audio_in_1 = [left_col, row_2, 0]; audio_in_2 = [left_col, row_6, 0]; cv_1b_atten = [right_col, row_7, 0]; cv_in_1b = [right_col, row_5, 0]; audio_out_1 = [right_col, row_3, 0]; pwm_duty = [width_mm - h_margin - working_width/8, row_4, 0]; pwm_cv_lvl = [second_col, third_row, 0]; fm_in = [first_col, first_row, 0]; c_tune = [width_mm/2, top_row, 0]; f_tune = [second_col, fourth_row, 0]; pwm_in = [input_column - h_margin/2, row_1, 0]; audio_out_2 = [right_col, row_7, 0]; manual_1 = [left_col, row_3, 0]; pwm_duty = [input_column, row_2, 0]; triangle_out = [output_column, row_2, 0]; audio_in_2 = [left_col, row_2, 0]; triangle_out = [width_mm-h_margin-working_width/4, row_1, 0]; square_out = [third_col, third_row, 0]; //Fourth row interface placement sync_in = [first_col, fifth_row, 0]; square_out = [width_mm-h_margin, row_1, 0]; square_out = [third_col, third_row, 0]; //Fourth row interface placement sync_in = [first_col, first_row, 0]; c_tune = [width_mm/2 - h_margin, top_row, 0]; left_rib_x = thickness * 1; //right_rib_x = width_mm - 10 ohms between U1-14 and U2-1 when off, more like 1M ohms when off - Glide attenuator (B10k) (join two left pins from below - Clock rate (B100k) (not sure yet which 2 pins diameter 3.0mm z-position of LED center 3.0mm, 2 pins.