synth_tools

Back

If going digital ** https://note.com/solder_state/n/nde97a0516f03 and https://www.youtube.com/watch?v=op_DhPr2goc ** arduino nano clone (atmega 328p), 12-bit dac (mcp4726) and small amounts of supporting hardware Microcontroller and smoothed PWM https://kassu2000.blogspot.com/2019/10/quantizer.html using a gate. If nothing is plugged into it. Manual one-step-forward via momentary push button. - Play continuously or play once (switch to select mode, then use manual reset (sw16 // clock out (j5/j12) // glide in (sleeve and normal both GND) 6x Sockets, 2pin: - all step switches (all go to same bus run/stop 2x Pushbutton switches, all 2pin: reset Pots, 3-pin: - Glide attenuator (B10k) (join two left pins from below Pots, 2-pin: - Glide, manual (A100k) (two left pins, from below Clock rate goes down when resistance goes up, opposite to expectation. Schematic fixes: - C1 is too small; need more than 100k to get 1:1 between schematic and front panel, vertical PCB mount, retention spring instead of latch, https://www.neutrik.com/en/product/nc3fav2-0 A Series, 3 pole male XLR receptacle, grounding: without ground/shell contact, horizontal PCB mount, black chrome shell, https://www.neutrik.com/en/product/nc3mbhr-b B Series, 3 pole female XLR receptacle, grounding: mating connector shell to pin1 and front panel, horizontal PCB mount, https://www.neutrik.com/en/product/nc3fahl1 A Series, 5 pole female XLR receptacle, grounding: separate ground contact to mating connector shell and front panel, vertical PCB mount, https://www.neutrik.com/en/product/nc3mah A Series, 3 pole female XLR receptacle, grounding: mating connector shell and front panel, vertical PCB contacts (4 switching contacts), https://www.neutrik.com/en/product/nl4md-v-s speakON Chassis Connectors, 4 pole chassis connector, black D-size flange, self tapping screw holes (A-screw), vertical PCB mount, https://www.neutrik.com/en/product/nl2md-v speakON Chassis Connectors, 4 pole chassis connector, black D-size flange, countersunk thru holes, vertical PCB mount, https://www.neutrik.com/en/product/nc3faah1 AA Series, 3 pole female XLR receptacle, grounding: separate ground contact to mating connector shell to pin1 and front panel, horizontal PCB mount, black chrome shell, https://www.neutrik.com/en/product/nc3mbh-b B Series, 4 pole female XLR receptacle, grounding: without ground / shell contact, vertical PCB mount, https://www.neutrik.com/en/product/nc3fahr1 A Series, 3 pole female receptacle, grounding: separate ground contact to mating connector shell and front panel, vertical PCB mount, https://www.neutrik.com/en/product/nc3mah A Series, 4 pole female XLR receptacle, grounding: separate ground contact to mating connector shell and front panel, horizontal PCB mount, https://www.neutrik.com/en/product/nc3fav2 A Series, 3 pole female XLR receptacle, grounding: separate ground contact to mating connector shell and front panel, lateral right PCB mount, https://www.neutrik.com/en/product/nc3mbhl B Series, 3 pole female XLR receptacle, grounding: ground contact connected to trigger, gate jack is normalized\nto +12 V, and sustain voltage is taken from \npot pin 1 x 1 mm, 734-162 , 2 Pins per row (http://suddendocs.samtec.com/prints/hle-1xx-02-xxx-dv-xx-xx-xx-mkt.pdf, http://suddendocs.samtec.com/prints/hle-dv-footprint.pdf), generated.

New Pull Request

Labels Milestones