Labels Milestones
BackSPT 2.5/12-V-5.0-EX 1732593 Connector Phoenix Contact, SPT 2.5/10-H-5.0-EX 1732467 Connector Phoenix Contact connector footprint for: MSTBV_2,5/12-GF-5,08; number of steps. Exact configuration TBD. One SPDT switch to disable reset (run once). - Momentary-normal-off pushbutton to manually reset. - One potentiometer per step, to set output voltages. (10) One potentiometer for internal clock signal (possibly external). Commonly called a "Baby 8", so called because it's a simple implementation. Can be done, but requires a trigger-sized pulse on input. Portamento (aka slew rate controller aka glide). - Knob version fairly simple. - CV Out - 1K to TP5 Gate Out - 1K to U2-14 - Casc Out normal to TP10, optional) - Casc Out - 1K to U2-14 - Casc Out normal to TP10, optional) - Casc out 2x Toggle Switches, 2pin: all step switches (all go to same bus) - run/stop 2x Pushbutton switches, all 2pin: - reset in - glide in (sleeve and normal both GND 6x Sockets, 2pin: - all step switches (all go to same bus run/stop 2x Pushbutton switches, all 2pin: - step - reset in - pause in - pause in - glide in (sleeve and normal both GND Glide attenuator (B10k) (join two left pins from below) Pots, 2-pin: Glide, manual (A100k) (two left pins, from below Pots, 2-pin: - Glide, manual (A100k) (two left pins, from below) Pots, 2-pin: - Glide, manual (A100k) (two left pins, from below Pots, 2-pin: Glide, manual (A100k) (two left pins, from below) - Clock Out - 1K to U2-14 Case Out - Diode from rotary pin 13 main synth_tools/3D Printing/Cases/Eurorack Modular Skeleton/Eurorack_box_v105.stl Executable file View File sr1_full.png Normal file Unescape Schematics/SynthMages.pretty/SOCKET_3_PIN_HEADER_NORMAL.kicad_mod Normal file Unescape Schematics/SynthMages.pretty/P160_pot_hole_nonpcb.kicad_mod Normal file View File Panels/FireballSpell_Large.webp Executable file View File 3D Printing/Pot_Knobs/Pot3.STL Executable file View File sr1_full.png Normal file Unescape // Width of module (HP) width = 36; // [1:1:84] working_height = height - hole_dist_top); cube([flange, flange, h], center=true); if (Pointer2==1 cube([8, 3, KnobHeight], center=true); if (RingWidth>0 cylinder(r1=KnobMajorRadius + RingWidth, r2=KnobMinorRadius, h=RingThickness, $fn=50, center=true); if (RingMarkings>0 for (i=[0 : RingMarkings-1] rotate([0, 0, 45] cube([2, 2, KnobHeight+.001], center=true); cube([RingWidth*.5, MarkingWidth, 2], center=true); if (style == "nut"){ From 76dd29636a4f24671e78194743554d11ed4d24e9 Mon Sep 17 00:00:00 2001 Subject: [PATCH] Add notes about UX component wiring 2x Sockets, all three pins need wires: glide in (sleeve and normal both GND 6x Sockets, 2pin: - step - reset in .
New Pull Request