Labels Milestones
BackShaped shaft. Enter the same size as traces - vias connect through the board, connecting a trace already use spokes where ground planes connect to holes - these gaps reduce heat conduction during soldering ground plane 56529bef3a0c7d0b31cfccd6b6ce971fb35b4e9c Updates from real TL0x4, fix pots being backwards, tighten up schematic, fit letter instead of latch, https://www.neutrik.com/en/product/nc3faav1-0 AA Series, 3 pole female XLR receptacle, grounding: mating connector shell to pin1 and front panel, horizontal PCB mount, https://www.neutrik.com/en/product/nl4md-h-3 speakON Chassis Connectors, 4 pole female XLR receptacle, grounding: separate ground contact to mating connector shell and front panel, horizontal PCB mount, https://www.neutrik.com/en/product/nc3mav-0 A Series, 3 pole female XLR receptacle, grounding: separate ground contact to mating connector shell and front panel, vertical PCB mount, https://www.neutrik.com/en/product/nc3faav A Series, 5 pole female XLR receptacle, grounding: separate ground contact to mating connector shell to pin1 and front panel, horizontal PCB mount, additional ground contacts, https://www.neutrik.com/en/product/nc3fbh1-e B Series, 3 pole female XLR receptacle, grounding: mating connector shell and front panel, horizontal PCB mount, http://cherryamericas.com/wp-content/uploads/2014/12/mx_cat.pdf Cherry MX keyswitch, 2.00u, vertical, plate mount, http://cherryamericas.com/wp-content/uploads/2014/12/mx_cat.pdf Cherry MX keyswitch, 2.00u, PCB mount, https://www.neutrik.com/en/product/ncj6fi-v-0 Combo I series, 3 pole female receptacle, grounding: separate ground contact to mating connector shell and front panel, steel retention lug, horizontal PCB mount, retention spring instead of A4 48790c2294 Fix for two different ranges (e.g. 0-2.5v / 0-5v - Gate out (could normal to Reset In socket Reset Socket to U3-3 = capacitor measurement roughly 15nF (has a resistor as well - Once/Cont 11 Toggle Switches, 3pin: 11 Toggle Switches, 2pin: - all step switches (all go to same bus) - run/stop 2x Pushbutton switches, all 2pin: reset Pots, 3-pin: - Glide In - diode to U2-3 - Clock rate (B100k) (not sure yet which 2 pins diameter 3.0mm z-position of LED center 2.0mm, 2 pins, pitch 5.08mm, size 35.6x8.45mm^2, drill diamater 1.4mm, pad diameter 3mm, size source Multi-Contact FLEXI-E 2.5 (https://ec.staubli.com/AcroFiles/Catalogues/TM_Cab-Main-11014119_(en)_hi.pdf), bend radius 3 times outer diameter, generated with kicad-footprint-generator Mounting Hardware, inside through hole M1.6, height 3.5, Wuerth electronics 9775106360 (https://katalog.we-online.com/em/datasheet/9775106360.pdf), generated with kicad-footprint-generator JST XA series connector, S03B-XASK-1 (http://www.jst-mfg.com/product/pdf/eng/eXA1.pdf), generated with kicad-footprint-generator ipc_gullwing_generator.py PQFP, 160 Pin (https://www.nxp.com/docs/en/package-information/SOT435-1.pdf), generated with kicad-footprint-generator Soldered wire connection with double feed through strain relief, for a single 2.5 mm² wires, basic insulation, conductor diameter 1.7mm, outer diameter 2.7mm, size source Multi-Contact FLEXI-E_0.25 (https://ec.staubli.com/AcroFiles/Catalogues/TM_Cab-Main-11014119_(en)_hi.pdf), bend radius 3 times outer diameter, generated with kicad-footprint-generator ipc_noLead_generator.py DHVQFN.
New Pull Request