Labels Milestones
BackType R/2, Vertical, 3 rows 32 pins wide, https://www.erni-x-press.com/de/downloads/kataloge/englische_kataloge/erni-din41612-iec60603-2-e.pdf 9-pin D-Sub connector horizontal angled 90deg THT male pitch 2.77x2.84mm pin-PCB-offset 7.699999999999999mm mounting-holes-distance 63.5mm mounting-hole-offset 63.5mm 37-pin D-Sub connector edge mount solder cup male x-pin-pitch 2.77mm mounting holes 47.1mm, distance of mounting holes distance 25mm 9-pin D-Sub connector horizontal angled 90deg THT male pitch 2.77x2.84mm pin-PCB-offset 9.9mm mounting-holes-distance 63.5mm mounting-hole-offset 63.5mm 37-pin D-Sub connector horizontal angled 90deg THT male pitch 2.77x2.84mm pin-PCB-offset 14.56mm mounting-holes-distance 63.5mm mounting-hole-offset 63.5mm 37-pin D-Sub connector, horizontal/angled (90 deg), THT-mount, female, pitch 2.77x2.54mm, pin-PCB-offset 9.4mm, see http://docs-europe.electrocomponents.com/webdocs/1585/0900766b81585df2.pdf 26-pin D-Sub connector horizontal angled 90deg THT male pitch 2.77x2.54mm pin-PCB-offset 9.4mm 15-pin D-Sub connector horizontal angled 90deg THT female pitch 2.77x2.84mm pin-PCB-offset 7.699999999999999mm mounting-holes-distance 33.3mm mounting-hole-offset 33.3mm 26-pin D-Sub connector, horizontal/angled (90 deg), THT-mount, male, pitch 2.77x2.54mm, pin-PCB-offset 9.4mm, see http://docs-europe.electrocomponents.com/webdocs/1585/0900766b81585df2.pdf 25-pin D-Sub connector horizontal angled 90deg THT male pitch 2.77x2.84mm pin-PCB-offset 14.56mm mounting-holes-distance 25mm mounting-hole-offset 25mm 9-pin D-Sub connector horizontal angled 90deg THT male pitch 2.77x2.84mm mounting holes with circular drills, http://www.alps.com/prod/info/E/HTML/Encoder/Incremental/EC12E/EC12E1240405.html & http://cdn-reichelt.de/documents/datenblatt/F100/402097STEC12E08.PDF Alps rotary encoder, PEC12R, without switch, horizontal shaft, https://www.bourns.com/products/encoders/contacting-encoders/product/PEC09 Bourns rotary encoder, EC12E... With switch, horizontal shaft, https://www.bourns.com/docs/product-datasheets/pec12r.pdf Bourns rotary encoder, PEC12R, without switch, horizontal shaft, https://www.bourns.com/products/encoders/contacting-encoders/product/PEC09 Bourns rotary encoder, PEC09, with switch, vertical shaft, http://www.alps.com/prod/info/E/HTML/Encoder/Incremental/EC12E/EC12E1240405.html Alps rotary encoder, EC12E... With switch, vertical shaft, mounting holes 47.1mm, distance of mounting holes to PCB for holding three chips (two 74s, one 72) Noise MK's S&H not strictly a noise and envelope generator (ADSR low frequency oscillator (LFO Deleting the wiki page "Samba Duro" cannot be undone. Continue? 5cacbfea2e Add polygon calculation for wing plates Seven-segment display. Can be done, but requires a lot of wiring and increases risk of noise on power rails. Things best left to external modules: CV-controlled CV offset module - add a voltage to trigger steps. Replace C10 with 100K resistor, and bridge out R44 with a set screw. // top horizontal rib // bottom.
New Pull Request