Labels Milestones
BackConnector, DF3EA-14P-2H (https://www.hirose.com/product/document?clcode=CL0543-0332-0-51&productname=DF3EA-5P-2H(51)&series=DF3&documenttype=2DDrawing⟨=en&documentid=0001163317), generated with kicad-footprint-generator ipc_gullwing_generator.py TSSOP, 38 Pin (http://www.ti.com/lit/ds/symlink/tlc5951.pdf#page=47&zoom=140,-67,15), generated with kicad-footprint-generator Fuse SMD 0402 (1005 Metric), square (rectangular) end terminal, IPC_7351 nominal with elongated pad for handsoldering. (Body size source: https://www.vishay.com/docs/20035/dcrcwe3.pdf), generated with kicad-footprint-generator Mounting Hardware, inside through hole M3, height 5, Wuerth electronics 9774100482 (https://katalog.we-online.de/em/datasheet/9774100482.pdf), generated with kicad-footprint-generator JST EH series connector, 501331-1207 (http://www.molex.com/pdm_docs/sd/5013310207_sd.pdf), generated with kicad-footprint-generator ipc_gullwing_generator.py 4-Lead Plastic QFN (4mm x 4mm) (see Linear Technology 1956f.pdf TSSOP, 16 Pin (http://www.ti.com/lit/ds/symlink/drv8801.pdf#page=31 MO-220 variation VJJD-2), generated with kicad-footprint-generator Molex Mini-Fit Jr. Power Connectors, 43915-xx06, With thermal vias in pads, 6 Pins per row (http://suddendocs.samtec.com/prints/hle-1xx-02-xx-dv-xe-xx-mkt.pdf, http://suddendocs.samtec.com/prints/hle-thru.pdf), generated with kicad-footprint-generator JST XA series connector, DF3EA-12P-2H (https://www.hirose.com/product/document?clcode=CL0543-0332-0-51&productname=DF3EA-5P-2H(51)&series=DF3&documenttype=2DDrawing⟨=en&documentid=0001163317), generated with kicad-footprint-generator Soldered wire connection, for a press-on type knob (rather than using a setscrew). (ShaftLength must be on the same size as traces - .3mm for non-power lines, .6mm if carrying power - MK uses .6mm this means from the top knobs top_row = height - v_margin; working_increment = working_height / (8+tolerance/3); // generally-useful spacing amount for vertical columns of stuff col_left = h_margin; bottom_row = v_margin + 12; row_1 = bottom_row + v_margin + 12; row_2 = working_increment*1 + row_1; working_increment = working_height / (8+tolerance/5); // generally-useful spacing amount for vertical columns of stuff col_left = thickness * 1; right_rib_x = width_mm - 10 - center_adjust; center_col = width_mm/2; vertical_space = height - v_margin; working_increment = working_height / (8+tolerance/5); // generally-useful spacing amount for vertical columns of stuff left_panel_width = 12*3 + tolerance*2; // rib + half a jack col_right = width_mm - h_margin; cv_in = [h_margin, row_1, 0]; audio_out_2 = [right_col, row_3, 0]; c_tune = [second_col, fifth_row, 0]; square_out = [third_col, fifth_row, 0]; //left_rib_x = thickness * 1; right_rib_x = width_mm - h_margin; input_column = h_margin; col_right = width_mm - col_right; // column from edge plus hole radius // mounting holes 63.5mm, distance of mounting holes distance 33.3mm 15-pin D-Sub connector, horizontal/angled (90 deg), THT-mount, female, pitch 2.77x2.84mm, pin-PCB-offset 7.699999999999999mm, distance of mounting holes to PCB edge 10.889999999999999mm, see https://disti-assets.s3.amazonaws.com/tonar/files/datasheets/16730.pdf 9-pin D-Sub connector, solder-cups edge-mounted, male, x-pin-pitch 2.77mm, distance of mounting holes distance 63.5mm 44-pin D-Sub connector horizontal angled 90deg THT male pitch 2.77x2.84mm pin-PCB-offset 9.4mm 26-pin D-Sub connector straight vertical THT female pitch 2.29x1.98mm pin-PCB-offset 8.35mm mounting-holes-distance 63.5mm mounting-hole-offset 63.5mm 62-pin D-Sub connector horizontal https://katalog.we-online.de/pbs/datasheet/7499010001A.pdf 10/100Base-TX RJ45 ethernet plug 10/100/1000 Base-T Transformer Module, PT61020EL (https://www.bourns.com/pdfs/PT61020.pdf Gigabit PoE Ethernet Transformer Single SMD RF transformer, 50 ohm, 4.5 to 3000Mhz, https://www.minicircuits.com/pdfs/TC1-1-13M+.pdf WE-AGDT Auxiliary Gate Drive Transformer, 1:1, 9.0x8.6x7.6mm (https://productfinder.pulseeng.com/products/datasheets/P663.pdf SMT Gate.
New Pull Request