Labels Milestones
BackRef="R29" Part="1" AR Path="/6091D1B4" Ref="S?" Part="1" AR Path="/60800A40" Ref="R?" Part="1" AR Path="/607ED812/609384DB" Ref="#FLG0102" Part="1" AR Path="/60C38349" Ref="R?" Part="1" AR Path="/607ED812/60800A40" Ref="R27" Part="1" AR Path="/607ED812/60A9C081" Ref="R13" Part="1" AR Path="/60C3833D" Ref="R?" Part="1" AR Path="/607ED812/609384DB" Ref="#FLG03" Part="1" AR Path="/60C38349" Ref="R?" Part="1" AR Path="/60C38343" Ref="R?" Part="1" AR Path="/607ED812/60B16110" Ref="J11" Part="1" AR Path="/607ED812/60A9C081" Ref="R13" Part="1" AR Path="/60C38349" Ref="R?" Part="1" AR Path="/6091D1B4" Ref="S?" Part="1" AR Path="/60802BB2" Ref="R?" Part="1" AR Path="/60800A40" Ref="R?" Part="1" AR Path="/607ED812/609384DB" Ref="#FLG03" Part="1" AR Path="/607ED812/60C38343" Ref="R22" Part="1" From 3d279dd88cba890e1ff05b6fd01cb5480b1f325e Mon Sep 17 00:00:00 2001 Subject: [PATCH] more fixes more fixes - Gate out (could normal to TP10, optional Once/Cont 11 Toggle Switches, 2pin: - all step switches (all go to same bus) - run/stop 2x Pushbutton switches, all 2pin: reset Pots, 3-pin: - Glide attenuator (B10k) (join two left pins from below Pots, 2-pin: Glide, manual (A100k) (two left pins, from below - Clock rate goes down when resistance goes up, opposite to expectation. Glide fix - Single-step button (SW13) isn't producing a high enough voltage to trigger steps. Replace C10 with 100K resistor, and bridge out R44 with a more complex module, several variations on the left sub-panel top_row = height - v_margin - title_font; saw_out = [third_col, third_row, 0]; saw_out = [h_margin + working_width/4, row_1, 0]; pwm_in = [width_mm - h_margin - working_width/8, row_4, 0]; pwm_cv_lvl = [width_mm - h_margin - working_width/8, row_2, 0]; pwm_in = [first_col, fourth_row, 0]; triangle_out = [width_mm-h_margin-working_width/4, row_1, 0]; saw_out = [third_col, third_row, 0]; saw_out = [output_column, row_2, 0]; fm_lvl = [second_col, second_row, 0]; //Third row interface placement triangle_out = [third_col, third_row, 0]; fm_lvl = [h_margin+working_width/8, row_2, 0]; cv_2b_atten = [right_col, row_7, 0]; cv_in_1b = [right_col, row_7, 0]; manual_1 = [left_col, row_7, 0]; manual_1 = [left_col, row_7, 0]; manual_1 = [left_col, row_6, 0]; audio_in_1 = [left_col, row_7, 0]; manual_1 = [left_col, row_1, 0]; pwm_in = [input_column - h_margin/2, bottom_row, 0]; pwm_pot = [input_column - h_margin/2, row_1, 0]; fm_pot = [input_column - h_margin/2, row_1, 0]; fm_in = [first_col, first_row, 0]; //Second row interface placement triangle_out = [third_col, third_row, 0]; //Fourth row interface placement saw_out = [h_margin + working_width/4, row_1, 0]; fm_pot = [input_column - h_margin/2, row_1, 0]; square_out = [width_mm-h_margin, row_1, 0]; audio_out_2 = [right_col, row_7, 0]; cv_in_1b = [right_col, row_1, 0]; left_rib_x = hole_dist_side + thickness; h_margin = hole_dist_side + thickness; output_column = width_mm - col_right + tolerance*4 + 2; // Website specifies a thickness of 2mm // for cylinder indentations, set.
New Pull Request