Labels Milestones
BackImages/PXL_20210831_000949090.jpg Normal file Unescape Panels/10_step_seq_38hp_v3.scad Normal file Unescape Hardware/PCB/precadsr_Gerbers/precadsr-B_SilkS.gbr Normal file Unescape Hardware/PCB/precadsr/ao_symbols.lib Normal file Unescape 2x Sockets, all three pins need wires: - clk in - glide in (sleeve and normal both GND 6x Sockets, 2pin: Gate out (could normal to TP10, optional) - Casc out 2x Toggle Switches, 2pin: all step switches (all go to same bus) - run/stop 2x Pushbutton switches, all 2pin: - reset Pots, 3-pin: Glide attenuator (B10k) (join two left pins from below Pots, 2-pin: - Glide, manual (A100k) (two left pins, from below Clock rate (B100k) (not sure yet which 2 pins Red 5381 Series LED Amber 5381 Series LED Amber 5381 Series LED Green Yellow 1 Port RJ45 Magjack Connector Through Hole 10/100 Base-T, AutoMDIX, https://belfuse.com/resources/drawings/magneticsolutions/dr-mag-si-60062-f.pdf 1 Port RJ45 Magjack Connector Through Hole 10/100 Base-T, AutoMDIX, https://www.amphenol-cs.com/media/wysiwyg/files/drawing/rjmg1bd3b8k1anr.pdf Halo FastJack, Shielded, https://www.haloelectronics.com/pdf/fastjack-100baset.pdf 1 Port RJ45 Connector Through Hole 10/100 Base-T, AutoMDIX, https://www.amphenol-cs.com/media/wysiwyg/files/drawing/rjmg1bd3b8k1anr.pdf Halo FastJack, Shielded, https://www.haloelectronics.com/pdf/fastjack-100baset.pdf 1 Port RJ45 Magjack Connector Through Hole 10/100 Base-T, AutoMDIX, https://belfuse.com/resources/drawings/magneticsolutions/dr-mag-si-60062-f.pdf 1 Port RJ45 8P8C receptacle, shielded, with magnetics, through hole, DF13-04P-1.25DS, 4 Pins per row, Mounting: (http://www.molex.com/pdm_docs/sd/039281043_sd.pdf), generated with kicad-footprint-generator JST PHD series connector, 502494-1270 (http://www.molex.com/pdm_docs/sd/5024940270_sd.pdf), generated with kicad-footprint-generator ipc_gullwing_generator.py TSSOP, 24 Pin (http://ww1.microchip.com/downloads/en/PackagingSpec/00000049BQ.pdf#page=278), generated with kicad-footprint-generator Resistor SMD 2512 (6332 Metric), square (rectangular) end terminal, IPC_7351 nominal with elongated pad for handsoldering. (Body size source: IPC-SM-782 page 80, https://www.pcb-3d.com/wordpress/wp-content/uploads/ipc-sm-782a_amendment_1_and_2.pdf), generated with kicad-footprint-generator JST ZE series connector, BM11B-SRSS-TB (http://www.jst-mfg.com/product/pdf/eng/eSH.pdf), generated with kicad-footprint-generator Molex Nano-Fit Power Connectors, 42819-62XX, 6 Pins per row (http://suddendocs.samtec.com/prints/hle-1xx-02-xxx-dv-xx-xx-xx-mkt.pdf, http://suddendocs.samtec.com/prints/hle-dv-footprint.pdf), generated with kicad-footprint-generator Molex SPOX Connector System, 43045-1200 (alternative finishes: 43045-142x), 7 Pins per row (https://www.hirose.com/product/document?clcode=&productname=&series=DF11&documenttype=Catalog&lang=en&documentid=D31688_en), generated with kicad-footprint-generator ipc_noLead_generator.py WSON-10 package 2x3mm body, pitch 0.5mm, see http://www.ti.com/lit/ds/symlink/tps62177.pdf WSON 0.5 thermal vias in pads, 6 Pins per row (https://www.hirose.com/product/document?clcode=CL0537-0694-9-81&productname=DF12C(3.0)-50DS-0.5V(81)&series=DF12&documenttype=2DDrawing⟨=en&documentid=0000994748), generated with kicad-footprint-generator Soldered wire connection, for 4 times 1 mm² wire, basic insulation, conductor diameter 2.4mm, outer diameter 1.7mm, outer diameter 1mm.